Land Pride RC2512 Series Скачать руководство пользователя страница 27

Страница: 27 / 60

Section 1: Assembly & Set-up

10/7/21

RC2512 Series 2 S/N Rotary Cutters 330-725M

Table of Contents

Refer to Figure 1-13:

Remove all stroke control spacers (#2) from center

hydraulic cylinder (#1) by spreading them apart at

the break line.

8. Start tractor and lower cutter until front skids are

resting on the ground or on support blocks.

9. Shut tractor down properly before dismounting. Refer

“Tractor Shutdown Procedure”

on page 14.

10. Replace stroke control spacers as needed to support

wheels at this position.

11. Move cylinder lift levers back and forth to release all

hydraulic pressure at the couplers.

Refer to Figure 1-14:

12. Attach park jack (#3) to jack mount (#12).

For detailed instructions, see

“Park Jack Assembly”

on this page.

13. Unhook hitch safety chain (#4) from tractor.
14. Unhook hydraulic hose (#7) from tractor duplex

outlet. Insert couplers through spring hose loop (#10)

to keep couplers out of the dirt.

15. Unhook wire harness (#13) from tractor outlet. Coil

wire harness and store over spring hose loop (#10)

with connector hanging down to keep moisture out.

16. Pull back on locking collar (#6) and pull driveline (#5)

from tractor power take-off shaft.

17. Collapse driveline (#5) by pushing tractor end of

driveline toward the splitter gearbox.

18. Store yoke end of driveline (#5) on the cutter hitch

support rest (#11). Do not store yoke end in the dirt.

19. Adjust park jack (#3) up until hitch weight is removed

from tractor drawbar.

20.

See Detail “B”:

Remove hairpin cotter (#2) and hitch

pin (#1).

21. Start tractor and drive tractor slowly forward several

feet while watching to make sure no components are

still hooked to the tractor.

22. Shut tractor down properly before dismounting.
23. Lower park jack until cutter is resting on its front skid

shoes.

24. Replace hitch pin (#1) as follows:

See Detail “A”:

If unhooking LP Performance

Hitch, store hitch pin (#1) in horizontal hitch holes.

Secure with hairpin cotter (#2)

See Detail “B”

: If unhooking standard clevis,

replace connecting pin (#1) in clevis (#9) and

secure with hairpin cotter (#2).

Stroke Control Spacers on Center Deck Lift Cylinder

Figure 1-13

Tractor Unhook (LP Performance Hitch Shown)

Figure 1-14

Park Jack Assembly

Refer to Figure 1-14:

1. Remove park jack (#3) from left-hand wing deck
2. Attach park jack (#3) to jack mount (#12) and secure

with detent pin (#8). Make sure detent pin is fully

inserted.

3. If park jack is not vertical, adjust jack angle according

“Park Jack Angle Alignment”

on page 24.

4. Adjust height of park jack (#3) until hitch is supported

by the park jack.

30626

37941

Содержание RC2512 Series





























































Результаты поиска

Содержание RC2512 Series

Отзывы:

Бренды по названию

Популярные бренды

Land Pride RC2512 Series, Руководство оператора

Результаты поиска

Содержание RC2512 Series

Отзывы:

Бренды по названию

Популярные бренды