Land Pride RC2512 Series Скачать руководство пользователя страница 19

Страница: 19 / 60

Section 1: Assembly & Set-up

10/7/21

RC2512 Series 2 S/N Rotary Cutters 330-725M

Table of Contents

Torque Requirements

See

“Torque Values Chart”

page 54 to determine

correct torque values when tightening hardware. See

“Additional Torque Values”

at bottom of chart for

exceptions to common torque values.

Unfold Wings

DANGER

To avoid serious injury or death:

•

Keep everyone out of the area where the wing decks will

unfold. One of the wing decks can fall suddenly.

•

Do not stand between transport tires and wing deck or be in

an area where the wings can pinch or fall on you while

removing shipping bar and cylinder transport locks. Make

sure no one else is in the area where they can become

pinched or crushed by unfolding wings. The wings can drop

suddenly causing serious bodily injury or death.

WARNING

To avoid serious injury or death:
Hydraulic fluid under high pressure will penetrate the skin or

eyes causing a serious injury. Wear protective gloves and

safety glasses or goggles when working with hydraulic

systems. Use a piece of cardboard or wood rather than hands

when searching for leaks. If an accident occurs, seek

immediate emergency medical care or gangrene may result.

DO NOT DELAY.

1. To ensure wings will unfold under their own weight,

unload cutter onto a flat, level, surface.

2. Back tractor up close to the front of the cutter.
3. Before dismounting tractor, put tractor in park or set

park brake, turn off tractor engine, and remove switch

key to prevent unauthorized starting.

4. Connect hydraulic hose to tractor remote outlet. If

tractor has float option on one of the outlets, connect

hydraulic hose to that outlet.

Refer to Figure 1-2:

5. Start tractor and raise center deck and both wings

fully up with tractor control lever.

6. Turn tractor engine off, and remove switch key.
7.

Separate transport lock bars (#1 & #2) from each

other by removing bolt (#3).

IMPORTANT:

DO NOT SEPARATE TRANSPORT

LOCK BARS BOLTED BETWEEN WINGS UNTIL

AFTER HYDRAULIC HOOK-UP TO TRACTOR.

NOTE: Refer to

Figure 1-3:

An overhead host

attached to the wing axles is recommended to assist

lowering wing decks safely.

NOTE: Refer to Figure 1-3:

A come-along may be

needed to pull wings together before wing transport

locks (#1 & #2) can be separated.

Transport Locks Shown in Factory Shipping Position

Figure 1-2

Transport Lock Removed & Secured

Figure 1-3

8. On the right-hand side, remove hairpin cotter (#4)

from storage pin (#5).

Refer to Figure 1-3:

9. Rotate right wing transport lock bar (#1) up to storage

lug (#6). Secure with existing hairpin cotter (#4).

10. Repeat steps 8 and 9 for the left-hand wing transport

lock bar (#2) shown in Figure 1-2.

11. Return to the tractor seat and start tractor engine.
12. With tractor hydraulic control lever, lower center deck

and both wings until center deck cylinder is against

cylinder stroke stops and wings are fully down.

13. Repeat steps 8 and 9 for the left-hand wing transport

lock bar (#2) shown in Figure 1-2.

37544

37545

Attach recommended overhead hoist to wing axle in this

location before lowering the wing deck.

Содержание RC2512 Series





























































Результаты поиска

Содержание RC2512 Series

Отзывы:

Бренды по названию

Популярные бренды

Land Pride RC2512 Series, Руководство оператора

Результаты поиска

Содержание RC2512 Series

Отзывы:

Бренды по названию

Популярные бренды