Land Pride RB16 Series, Руководство оператора, Страница: 16 / 32

Section 2: Accessory Equipment Set-Up
Table of Contents
9/28/18 RB1660, RB1672, RB1684, RB2672, RB2684, & RB2696 Rear Blades 301-375M
12
RB16 & RB26 Skid Shoes
Kit Bundle (Pair of skid shoes)
301-330ASKID SHOE ASSEMBLY
Refer to Figure 2-3:
The skid shoes can be attached to both ends of the
moldboard to help keep the cutting blade from damaging
the surface being bladed.
1. Remove two 5/8"-11 x 1 3/4" GR5 plow bolts (#4)
from end of blade. Keep hardware for reuse.
2. Attach skid shoe bracket (#2) to moldboard with
5/8"-11 x 1 3/4" GR5 plow bolts (#4) and hex flange
locknuts (#6). Tighten nuts to the correct torque.
3. Make certain the edge with 4 dimples in the skid shoe
slide bar are positioned to the back as shown. Insert
skid shoe (#1) into bracket (#2).
4. Push skid shoe up until hole “A” is above bracket (#2)
and insert hairpin (#7) in hole “A”. Bend one or more
legs of hairpin to keep it from falling out.
5. Screw 1/2" jam nut (#5) onto 1/2"-13 x 2" GR5 square
head set screw (#3). Push up on skid shoe (#1) and
screw set screw (#3) into bracket (#2) until tight
against bottom dimple “B”.
6. Tighten jam nut (#5) against bracket (#2).
7. Repeat steps 1 through 6 for the other side.
RB26 End Plates
Kit Bundle (Pair of End Plates)
301-010AEND PLATES
Refer to Figure 2-4:
The End Plates can be attached to both ends of the RB26
Series moldboard to help contain material while moving
the material from one location to another.
1. Position end plate (#3) against moldboard with
bottom of end plate flange approximately 1 1/4" up
from bottom of blade cutting edge and side of end
plate flange flush with right-hand end of moldboard.
2. Mark location of holes to be drilled on moldboard.
Hole location should be located approximately center
of slots in end plate flange.
3. Center punch and drill two 9/16" diameter holes in
moldboard.
4. Attach right-hand end plate (#3) to moldboard as
shown with two 1/2"-13 x 1 1/2" GR5 hex head cap
screws (#4), spring lock washers (#1), and hex
nuts (#2). Tighten hardware to correct torque.
5. Repeat step 1-4 for the left-hand end plate.
Rake Assemblies
Refer to Figure 1-1 on page 6:
1.
Remove
blade
assembly (#5) from main frame (#2).
Refer to Figure 2-5:
2. Attach any one of the rake assemblies (#1) to the
main frame (#2) shown in Figure 1-1 on page 6.
RB16 & RB26 Series Skid Shoes
Figure 2-3
RB26 Series End Plate Assembly
Figure 2-4
Rake Assembly (LR1696 Shown)
Figure 2-5
Kit Bundles For LR16 Series Rear Blades
302-278S . . . . . . . . . . . 60" LR16 SERIES RAKE ASSEMBLY
302-280S . . . . . . . . . . . 72" LR16 SERIES RAKE ASSEMBLY
302-287S . . . . . . . . . . . 84" LR16 SERIES RAKE ASSEMBLY
302-288S . . . . . . . . . . . 96" LR16 SERIES RAKE ASSEMBLY
Kit Bundles For LR26 Series Rear Blades
302-295S . . . . . . . . . . . 84" LR26 SERIES RAKE ASSEMBLY
302-296S . . . . . . . . . . . 96" LR26 SERIES RAKE ASSEMBLY
33272
25528
33889
1