Land Pride NTS2607 Скачать руководство пользователя

Страница: 40 / 78

Section 3: Roller Adjustments

NTS2607, NTS2609, & NTS2611 No-Till Seeder 329-141M

Table of Contents

9/10/20

Section 3: Roller Adjustments

Front Spike Roller Adjustment

(Gang Slide #2 Shown Positioned Fully Back)

Figure 3-1

Front Spike Roller Angle

Refer to Figure 3-1:

1. Lower the seeder frame onto support blocks to keep

the front rollers just above ground level and allowing

them to move freely.

2. Shut tractor down before dismounting. Refer to

“Tractor Shutdown Procedure”

on page 21.

3. Remove bent pins (#6).

4. If needed, readjust flange lock nuts (#4) as follows:

a. Remove cotter pin (#8), flat washer (#9) and

clevis pin (#7).

b. With an extension, tighten locknuts (#4) until they

are snug against gang slide (#2) and then back-

off 1/3 turn (2 hex flats). Additional back-off may

be required if the gang slide does not move easily.

c. Replace clevis pin (#7), flat washer (#9), and

cotter pin (#8). Bend one or more legs of the cotter

pin to keep it from falling out.

5. Operate roller angle lever (#1) to position front rollers

(#3) to the desired angle.

6. Replace bent pins (#6) with one on each side of gang

slide (#2). Secure bent pins with hair pin cotters (#5).

7. Start tractor, remove support blocks, and lower

seeder to ground level.

39016

73659

NOTE:

Gang slide (#2) is shown in its furthest back

position. In this position, both bent pins (#6) are in

front of the gang slide as shown. In all other

positions, one bent pin is in back of the gang slide

and the other is in front of the gang slide.

IMPORTANT:

Lock nuts (#4) are factory adjusted to

allow gang slide (#2) to move easily with minimum

gap between the lock nuts and gang slide.

Mud Scraper Adjustments

Figure 3-2

Mud Scrapers

Refer to

“Torque Values Chart for Common Bolt Sizes”

on page 72 when tightening hardware.

Refer to Figure 3-2:

Adjust Front Mud Scrapers

1. With the front rollers off the ground, loosen 3/8"-16

hex bolts (#1 & #2) at both ends of the left front mud

scraper (#3).

2. Rotate teeth of the mud scraper towards the front

roller to increase removal of mud and debris and

away if scraper teeth are interfering with the roller.

3. Tighten the four 3/8"-16 GR5 hex head

bolts (#1 & #2) to the correct torque.

4. Repeat steps 1, 2, & 3 above for the right front mud

scraper.

5. Loosen hex flange lock nuts (#4) and adjust front

scrapers (#3) left or right to align slots up with the

roller spikes. Rotate spike rollers one or more full

revolutions to verify spikes are not touching the

scraper teeth.

6. Tighten 3/8"-16 hex flange lock nuts (#4) to the

correct torque.

Adjust Rear Mud Scrapers

1. Loosen 3/8"-16 hex lock nuts (#5 & #6) at both ends

of the rear mud scraper (#7).

2. Rotate teeth of mud scraper toward the front roller to

increase removal of mud and debris and away if

scraper teeth are interfering with the roller.

3. Tighten the four 3/8"-16 GR5 hex head bolts and lock

nuts (#5 & #6) to the proper torque.

73480

Содержание NTS2607















































































Результаты поиска

Содержание NTS2607

Отзывы:

Похожие инструкции для NTS2607

Бренды по названию

Популярные бренды

Land Pride NTS2607, Руководство оператора

Результаты поиска

Содержание NTS2607

Отзывы:

Похожие инструкции для NTS2607

Бренды по названию

Популярные бренды