Land Pride FPS48 Скачать руководство пользователя страница 21

Страница: 21 / 38

Section 3: Adjustments

FPS48 Plot Ranger Food Plot Seeder 322-118M

12/7/18

Table of Contents

Disc Gang Adjustments

WARNING

To avoid serious injury or death:

•

Be careful when working with disc blades as the edges are

sharp. Wear gloves when working around disc blades. Keep

others away.

•

Properly block and secure disc in the raised position prior to

changing gang angles, gang position, disc replacement or

during maintenance. Keep feet out from under the disc blades

during adjustments or maintenance.

•

Perform maintenance only on equipment that is not

running. Place power machine in park or set park brake,

shut engine off, remove switch key, and wait for all moving

components to come to a complete stop before dismounting.

Park implement on a flat, level surface.

2. Place power machine in park or set park brake, shut

engine off, and remove switch key before
dismounting. Also, refer to shutdown instructions in
the power machine Operator’s Manual.

3. Place support blocks/jack stands under the main

frame and lower the disc onto the supports.

Disc Adjustments

Figure 3-1

Disc Gang Angle

Refer to Figure 3-1:

The Plot Ranger is designed for ease of angling with the
front and rear discs having four angle positions:
(0, 7, 14, and 21 degrees.) Disc angle in Figure 3-1 are
shown at 14 degrees.

Remove hairpin cotter and hitch pin.

2. Slide disc gangs to desired position and replace hitch

pin. Secure hitch pin with hairpin cotter.

23911

Clevis Pin and Hair Pin Cotter

Adjustment
Holes

NOTE:

Increasing disc gang angle makes for a more

aggressive cut to remove more vegetation and
requires more horsepower to pull the implement.

Decreasing disc gang angle will give a better ground
finish, remove less vegetation, and requires less
horsepower.

Disc Gang Position

Refer to Figure 3-2:

WARNING

To avoid serious injury or death:
Do not remove u-bolt nuts to reposition the disc gangs. Only

loosen them. If u-bolt nuts are removed, disc gangs will drop

causing injury to the body.

Loosening u-bolts (#1) and sliding the disc gangs in
or out to desired position. The recommended
position is 2" from end of steel tube as shown

2. Tighten u-bolts to the proper torque once the gangs

have been set to the desired position.

Disc Adjustments

Figure 3-2

Disc Blade Replacement1vb

Refer to Figure 3-3:

When replacing notched disc blades, assemble disc
blades with the notches in a spiral pattern as shown.

Disc Replacement (Spiral)

Figure 3-3

23912

23911

Section 3: Adjustments

Содержание FPS48







































Результаты поиска

Содержание FPS48

Отзывы:

Похожие инструкции для FPS48

Бренды по названию

Популярные бренды

Land Pride FPS48, Руководство оператора

Результаты поиска

Содержание FPS48

Отзывы:

Похожие инструкции для FPS48

Бренды по названию

Популярные бренды