Land Pride FDR3690 Скачать руководство пользователя страница 21

Section 3: Operating Instructions 

Table of Contents

11/7/18

FDR3690 Rear Discharge Grooming Mower 310-447M

17

8. Investigate the cause of vibration. Make necessary 

corrections before continuing.

Transporting

WARNING

!

To avoid serious injury or death:  

When traveling on roadways, travel in such a way that 

other vehicles may pass you safely. Use LED lights, clean 
reflectors, and a slow moving vehicle sign that is visible 
from the back to warn operators in other vehicles of your 
presence. Always comply with all federal, state, and local 
laws.

Select a safe ground speed when transporting. Never travel 

at a speed which does not allow adequate control of steering 
and stopping, and never exceed 20 mph (32.2 km/h) with 
attached equipment. Rough terrain requires a slower speed.

1.

When raising mower to transport position, be sure 
driveline does not contact tractor or mower. Adjust 
and set tractor’s 3-Point hitch lift height so that the 
power take-off shaft does not contact mower deck in 
the fully raised position.

2. Be sure to reduce tractor ground speed when turning 

and leave enough clearance so the mower does not 
contact obstacles such as buildings, trees, or fences.

3. Select a safe ground speed when transporting from 

one area to another. 

4. When traveling on roadways, transport in such a way 

that faster moving vehicles may pass you safely. A 
slow moving vehicle sign should always be properly 
displayed when traveling on public roads or right-of-
ways.

5. Shift tractor to a lower gear when traveling over rough 

or hilly terrain.

Safety Information

DANGER

!

To avoid serious injury or death:  

Do not allow anyone near the tractor or implement while 

operating. Stop operation if bystanders are too close. They 
can be hit by flying projectiles, become entangled in the 
equipment, or ran over.

Tractor power take-off shaft shield, driveline shields, and 

gearbox shaft shields must be installed and in good working 
condition to avoid driveline entanglement and projectiles 
flying off of the driveline.

Do not engage power take-off while hooking-up or 

unhooking the driveline, or while someone is standing near 
the driveline. A person’s body and/or clothing can become 
entangled in the driveline.

NOTE:  

Always disengage power take-off before 

raising mower to transport position.

Always disconnect driveline from the tractor before 

servicing the drivetrain and components powered by the 
drivetrain. A person can become entangled in the drivetrain 
if the tractor is started and the power take-off is engaged.

All V-belt guards must be in good working condition and 

installed before power take-off is engaged. Never allow 
fingers, hands, or other body extremities to come near a 
moving V-belt or pulley. Doing so can result in server bodily 
injury or death.

Never place hands or feet under the deck or attempt to make 

adjustments to the mower with PTO engaged. Mower blades 
rotating at high speeds cannot be seen and are located close 
to the deck housing. Body extremities will be cut instantly.

Clear area to be cut of debris and unforeseen removable 

objects before mowing. Mark any potential hazards that 
cannot be removed such as dirt mounds, tree stumps, posts, 
large rocks, holes, and drop-offs with a visible flag.

Always disengage power take-off before lifting implement 

up, and never operate implement in the raised position. 
Objects can be thrown at high speeds toward people or 
animals

Do not use mower blades for a fan. Mower blades are not 

properly designed or guarded for this use. Using mower 
blades as a fan can result in serious injury and/or death.

Make certain driveline yokes are securely fastened at each 

end. A loose yoke can work free allowing the driveline to 
rotate uncontrollably causing implement damage and 
bodily injury or death to anyone nearby.

Do not use a power take-off adapter. The adapter will 

increase strain on the tractor’s power take-off shaft causing 
possible damage to shaft and driveline. It will also defeat 
the purpose of the tractor’s power take-off shield.

WARNING

!

To avoid serious injury or death:  

Do not use implement as a man lift or work platform. It is 

not properly designed or guarded for this use.

Do not use implement to lift objects; to pull objects such as 

fence posts, stumps, etc; or to push objects. The unit is not 
designed or guarded for these uses.

Always shut tractor down using “Tractor Shutdown 

Procedure” provided in this manual before dismounting 
tractor.

Never carry riders on the implement or tractor. Riders can 

obstruct the operator’s view, interfere with control of the 
equipment, be pinched by moving components, become 
entangled in rotating components, be struck by objects, be 
thrown or fall from the equipment, etc.

Do not operate and/or travel across inclines where tractor 

and/or implement can roll over. Consult your tractor’s 
manual for acceptable inclines the tractor is capable of 
traveling across.

Содержание FDR3690



































Отзывы: