Land Pride AFM4522 Скачать руководство пользователя страница 26

Страница: 26 / 58

Section 1: Assembly & Setup

Table of Contents

AFM4522 All-Flex Grooming Mower 315-360M

11/18/21

Install LED Lights

Refer to Figure 1-13:

LED lights are mounted at an angle to be viewable from

the rear while transporting with center deck raised.
Each LED light fixture is supplied with two amber lens

and one red lens. The lights are mounted with one amber

lens facing forward and one facing reward. The rear

facing amber lens must be positioned above the rear

facing red lens.
Light mounting brackets (#2) are mounted with 2" x 9" red

reflector decals facing rearward and rectangle holes

(B1 & B2) facing forward.
1. On the right-hand side, rotate light bracket (#2) to the

angle shown with hole (B1) facing forward. Attach

mounting bracket (#13) with 1/2"-13 x 1 1/2" GR5 hex

head bolts (#1) and hex flange locknuts (#3). Tighten

locknuts to the correct torque.

2. Locate LED light (#6). It will have one amber lens

facing forward and one facing reward with the rear

facing amber lens above the rear facing red lens.

3. Thread connector (A1) through hole (B1).
4. With amber lens above rear facing red lens, attach

LED light (#6) to light mounting bracket (#2) using

1/4"-20 x 1" GR5 hex head bolt (#4), flat washer (#5),

and hex nylock nut (#8). Tighten nylock nut (#8) to

the correct torque.

5. Uncoil wire harness (#11) and attach connector (C1)

to LED light connector (A1).

6. On the left-hand side, rotate light bracket (#2) to the

angle shown with hole (B2) facing forward. Attach

mounting bracket (#14) with 1/2"-13 x 1 1/2" GR5 hex

head bolts (#1) and hex flange locknuts (#3). Tighten

locknuts to the correct torque.

Thread connector (A2) through hole (B2).

8. With amber lens above rear facing red lens, attach

LED light (#7) to light mounting bracket (#2) using

1/4"-20 x 1" GR5 hex head bolt (#4), flat washer (#5),

and hex nylock nut (#8). Tighten nylock nut (#8) to

the correct torque.

9. Uncoil wire harness (#12) and attach connector (C2)

to LED light connector (A2).

10. Check connections at enhance module (#10) to

make sure wire harness (#11 & #12) are securely

connected to the module connectors.

11. With zip ties (#9), attach wire harnesses (#11 & #12)

to the gauge wheel arms and slots (D) as needed.

12. Check wire harness routing to make sure wires will

not be pinched as the decks are folded and unfolded

and while raising and lowering the mower.

LED Light Assembly

Figure 1-13

NOTE:
LED LIGHTS (#6 & #7) ARE MOUNTED
WITH REAR FACING AMBER LENS
ABOVE REAR FACING RED LENS.

Содержание AFM4522



























































Результаты поиска

Содержание AFM4522

Отзывы:

Похожие инструкции для AFM4522

Бренды по названию

Популярные бренды

Land Pride AFM4522, Руководство оператора

Результаты поиска

Содержание AFM4522

Отзывы:

Похожие инструкции для AFM4522

Бренды по названию

Популярные бренды