manualshive.com logo in svg

Land Pride 945551+, Руководство оператора

Поделиться
Скачать
Land Pride 945551+ Скачать руководство пользователя страница 22

18

Section 1: Assembly & Set-up

RC2512 Series 2 S/N Rotary Cutters 330-725M

9/6/17

Table of Contents

Remove Shipping Lugs

Figure 1-9

Remove Shipping Lugs

Refer to Figure 1-9:

The shipping lugs (#1) will interfere with wheels on both 
sides of the center deck and must be removed.

1.

Unbolt 1/2" hardware (#2) and remove shipping 
lugs (#1) from both sides of the center deck.

2.

Discard removed hardware (#2) and shipping 
lugs (#1).

37526

Stroke Control Spacers on Center Deck Lift Cylinder

Figure 1-10

Driveline Clearance Check

Refer to Figure 1-10:

Check driveline for adequate clearance under all ranges 
of cutter height.

1.

With driveline attached to the tractor and all stroke 
control spacers (#2) removed from hydraulic 
cylinder (#1), slowly raise and lower cutter to its 
upper and lower limits while observing clearances 
between hitch and driveline. 

2.

If driveline interferes with tractor drawbar, then adjust 
drawbar height and length. See 

“Drawbar Set-up” 

on page 12 for correct placement of tractor drawbar.

3.

It may be necessary to purge lift cylinder (#1), wing 
cylinder, and hydraulic hoses of trapped air if 
operation is sluggish. Cycle cylinders back and forth 
several times to purge air from them. For additional 
details, see 

“Purge Hydraulic System” 

on page 19.

30626

NOTE:  

The lift cylinder should raise cutter up while 

pulling the control lever back and lower cutter while 
pushing lever forward. Switch connections at the 
duplex outlet if lift control lever works opposite.

Содержание 945551+

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды