Land Pride 472620 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 72

background image

39

SECTION 4: ELECTRICAL SYSTEM

9/24/09

Z44 and Z52 Accu-Z Razor (S/N 472620 and above) Riding Mowers 357-044SM

Land Pride

WIRING HARNESS INSTALLATION

1. Align and install wiring harness by starting at front of
unit.

2. Feed brake sensor cable behind battery tray and the
operator presence switch wire through back of frame and
out mounting hole.

3. Secure the front portion with cable tie.

photo zsm254

4. Feed control panel harness through fuel tank and
connect to the control panel. See control panel
installation on page 21.

5. Connect wiring harness to the engine regulator/
rectifier.

6. Align and install wiring harness to engine wiring
harness, starter power and common ground.

photo zsm129

7. Align and install engine oil pressure sensor.

8. Secure wiring harness with cable ties. Ensure to
capture all hanging hoses and cables.

9. Connect the battery and test for operation.

photo zsm048

«
...
37
38
39
40
41
...
»

Содержание 472620









































































Отзывы:

Нет отзывов

Похожие инструкции для 472620

Бренд: Jacobsen Страницы: 20

Бренд: McCulloch Страницы: 36

PowerMax 1200/32

Бренд: Gardena Страницы: 352

Бренд: Gardif Страницы: 21

Бренд: MTD Страницы: 16

Wheel Horse 265-6

Бренд: Toro Страницы: 44

Бренд: Jacobsen Страницы: 36

GRASS KEEPER 190 W

Бренд: Garland Страницы: 136

TURF TIGER STT61V-31KB-DF

Бренд: Scag Power Equipment Страницы: 78

Бренд: MTD Страницы: 20

Бренд: FGM Страницы: 33

STOCKMAN 4000A16514E

Бренд: COX Страницы: 48

Бренд: Grizzly Страницы: 148

Бренд: Dolmar Страницы: 248

Бренд: LawnMaster Страницы: 16

Бренд: hillvert Страницы: 210

Бренд: Craftsman Страницы: 30

Бренд: Craftsman Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды