Land Pride 357-044M Скачать руководство пользователя страница 42

Страница: 42 / 48

Section 5: Specifications & Capacities

Z44 & Z52 (S/N 472620 -526170) Zero Turning Radius Mowers Riding Mowers Accu-Z Razor

357-044M

2/27/07

Land Pride

Table of Contents

Ground Speed

Forward: 0-7 MPH
Reverse: 0-5 MPH

Steering Type

Twin lever steering provides independent control of each drive wheel.

Twin Lever Steering Controls

Speed, forward, reverse, brake, and turns.

Steering Turning Radius

True zero degree. Turns with counter-rotating independent drive wheels

Brake Service

Hydrostatic dynamic braking

Parking

Lever applied pawl and cog wheel

Mower Drive

Single V-belt with electric clutch and spring tension idler pulley

Safety Features

Operator presence system connected to deck and drive clutches.

Seat

Molded-vinyl seat. Bolt loosening required for forward and reverse adjustments.

Optional armrests kit for standard molded-vinyl seat.

Optional deluxe cushion seat with arm rests.

Mainframe Construction

1 1/2" square solid steel.

Drive Motor Mount

1/8” welded steel

Front Caster Wheels

Mounted with roller bearings on each wheel.

Front Caster Forks

3/8” steel.

Deck Thickness

11 Gauge decks with reinforcements welded into spindle mount areas

Box-Section Reinforced Front
Edge

11 GA. x 3 1/2" x 1 1/2” Box

Deck Trim Edges

Solid 1” x 3/8” steel bars for reinforced impact area

Deck Housing Depth

4 1/8” deep, (room for high-capacity mowing)

Deck Lift

Foot-operated deck height adjustment.

Pin for setting height and transport position.

Hand Operated Controls

Ignition switch, throttle lever, control levers, blade engagement switch,

choke lever and Left/Right Fuel Tank Valve.

Indicators

Engine warning light and hour meter

Cup Holder

Two cup holders molded into the left side fuel tank.

Accommodates nearly any cup size including Big Gulp.

Cutting Heights

Foot-operated deck height adjustment. Pin for setting height, transport position.

Height adjustment in 1/4" increments from 1 1/2” to 4 1/2”

Mowing Blades

Heavy-duty, heat-treated, high-lift steel blades

.20" x 2 1/2" x 15.81"

.20 x 2 1/2” x 17.81”

Blade Tip Speed

16,811 FPM

18,937 FPM

Blade Drive

V-belt drive to all three spindles. Spring tension idler pulleys.

Spindles

Machine ductile housing, 1" diameter high carbon steel shafts

and greasable ball bearings.

Flotation

Free-floating mower using three blades with center blade to the front.

Mower is suspended at the four corners on spring-assisted chains.

Includes 4 anti-scalp wheels to improve flotation in rolling and uneven terrain.

Z44 & Z52 Accu-Z Razor

(General Specifications)

Z44

Z52

Содержание 357-044M

















































Результаты поиска

Содержание 357-044M

Отзывы:

Бренды по названию

Популярные бренды

Land Pride 357-044M, Руководство оператора

Результаты поиска

Содержание 357-044M

Отзывы:

Бренды по названию

Популярные бренды