LP-2354
EXTERNAL 5 Port PoE Unmanaged 10/100Mbs Switch/Extender
(4 Ports Full PoE Power-up to 15.4 Watts per Port with 1 Uplink Port up to 100Mbs)
Installation Guide
Purpose of this Guide
This Guide provides information and procedures for the product installation and operation of the 5 Port PoE
Unmanaged 10/100Mbs Switch/Extender (LP-2354). This document is intended for technical personnel and
to use this document effectively, you should have a working knowledge of Local Area Networking (LAN)
concepts and hardware installation. In addition, you should be familiar with the following: Connection of
Patch Cables with RJ45 connectors and the LAN addressing map for your particular Network, Mounting of
Network hardware in a 19” equipment rack and local practices for power cord connections.
IMPORTANT SAFETY INSTRUCTIONS FROM LAN Power
Read and keep these instructions. Follow all instructions and heed all warnings. Although the IP67 Housing
is weather resistant rated – DO NOT submerge this equipment in water. Install in accordance with
manufacturer’s instructions. Unplug this equipment during lightning storms or when unused for long
periods of time. Refer all servicing to qualified service personnel. Servicing is required when the equipment
has been damaged in any way, liquid has been spilled, or object has fallen into the equipment, the internal
electronic equipment has been exposed to rain or moisture, does not operate normally, or has been dropped.
The AC mains outlet, or appliance coupler shall be readily available to the operator as a means of power
disconnection.
CAUTION
– These servicing instructions are for use by qualified service personnel only. To reduce the risk of
electric shock, do not perform any servicing other than that contained in the operating instructions unless
you are qualified to do so.
If You need Help
or additional support relating to the contents of this Guide, please contact LAN Power
using one of the following methods: Phone: 1-510-275-4572 Fax: 1-510-824-5654 Mail: LAN Power, 47835
Westinghouse Drive, Fremont, CA 94539 Web Address: www.lan-power.com Email: [email protected]
Before contacting LAN Power for technical support
, please have the following information ready: the
product model number and unit serial number, a description of the failure or symptoms of problem. A
description of any action(s) already taken to resolve the problem (e.g., changing ports, rebooting the unit,
etc...). The type of End device being powered including Manufacturer name and part number and powering
requirements of the IP End Device. A description of your Network environment (layout, Ethernet switch
description, cable type, etc...). The unit history (i.e., have you returned the unit before, is this problem a
recurring problem, etc...)
Please note only qualified personnel should install this unit and
read instructions before attempting to install this unit
Verifying Contents of Package
- Unpack the PoE Injector and verify that you have the
following items: LP-2354 5 Port PoE Unmanaged 10/100Mbs Switch/Extender
NOTE
: THE LP-2354 DOES NOT INCLUDE A POWER SUPPLY and MUST BE PURCHASED
SEPERATELY. Use either the LAN Power
LP-2575
(Single Port ULTRA High Power Midspan
PoE Injector) or
LP-2304PSU
(AC Mains Power Supply Unit)
Technical Considerations
-
Before you mount the 5 Port PoE Unmanaged 10/100Mbs Switch/Extender
to a fixed location, consider all of the following: Determine optimal placement, check patch cord routing
and AC outlet location. Collect and document Network information as required. Ensure the CAT 5 (or
higher) cable length from the LP-2354 to the Powered End IP device does not exceed 328 feet/100 meters
total length.
Powering Up and Installing the 5 Port PoE Unmanaged 10/100Mbs Switch/Extender
1.) Remove the Back Mounting Plate from the IP67 External Housing which is done by removing the 4 screws
- (2 on left side and 2 on right side)
2.) Mount the Back Mounting Plate to desired location (Wall, Pole, etc.) – Mounting Fixing NOT INCLUDED
3.) Mount the IP67 Housing to the Back Mounting Plate with the 4 screws (2 on left side and 2 on right side)
4.) Bring all LAN Data Cables into the IP67 Enclosure via the 3 separate wiring glands provided. Please note
that the Right Wiring Gland has a single wire grommet and should be used for the powering of the LP-2354.
The incoming power is not supplied with the LP-2354 and the LP-2575 (Single Port ULTRA High Power
Midspan PoE Injector) or LP-2304PSU (AC Mains Power Supply Unit) must be used to power the LP-2354. The
Middle and Left Wiring Glands are supplied with a 2 (two) LAN Data Cable wiring gland and these should be
IEEE 802.3af
Compliant
