Lamtec CMS Скачать руководство пользователя страница 224 | Manualshive

Страница: 224 / 284

background image

223

8

CO/O

2

Control

Deactivating CO control depending on the O

2

value

For a description, see chapter

Optimising the CO Control

NOTICE

This function is only available via CMS Remote Software.

8.10.6 Checking the Combustion-related Limit Values

NOTICE

With O

2

trim is it essential to ensure that the burner burns safely and stably at maximum cor-

rectional intervention (0 % and 100

%), taking into account all environmental influences and

in every burner firing-rate range.
To do this, transverse the correction value both to 0 % and to 100

% at different firing-rate val-

ues (for CMS Remote Software see chapter

Testing the Correction Effect

8.10.7 Set and Optimise the CO Response Threshold on LT3-F

The basis for CO regulation is a digital signal



CO greater/less than threshold value.

This signal is formed in the LT3-F and transferred to the burner controller via the LAMTEC
SYSTEM BUS (LSB).
1. Run the burner to a firing-rate between base fire and half fire.
2. Change the electronic ratio towards less air and/or more fuel (correction values



100%)

until the CO edge is detected; if necessary, increase the correctional range again.
Alternatively, you can keep it regulated at the CO edge. You must not change the firing-
rate for this purpose (MANUAL burner firing-rate controller). On the display of the CMS,
the signal dynamics must rise continuously.

NOTICE

If this display value of CMS reaches -32 in case of air reduction (display of Item 2 = – and Item
4 = 32) and +52 or +54 ( in case of air increase (display of Item 2 = + and Item 4 = 52 or 54),
the CO regulation has detected the CO edge and the optimisation point is saved.

Repeat at another firing-rate point.

Fig. 8-14 ’Settings’ menu in the LT3-F

Can only be set in access level 2!
CO

e

trigger threshold. Switching threshold of

the CO

e

detection for LAMTEC CO/O

2

regu-

lation. Evaluation of the signal dynamics.
Settable in a range from 0 ... 100 %.
Factory setting: 40 %
< 40% trim becomes more sensitive
> 40% trim becomes less sensitive

«
...
222
223
224
225
226
...
»

Содержание CMS





























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CMS

Бренд: Rain Bird Страницы: 48

Бренд: 7bit Страницы: 2

Бренд: Jafar Страницы: 15

Бренд: Abus Страницы: 12

Бренд: Bartlett Страницы: 5

Бренд: LaserBit Страницы: 69

Бренд: Lawler Страницы: 5

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Watts Страницы: 24

Бренд: York Страницы: 24

Бренд: Eaton Страницы: 10

Бренд: Idemia Страницы: 29

MicroTech II UV05

Бренд: AAF Страницы: 50

Бренд: KanDao Страницы: 265

Бренд: WAGO Страницы: 16

Бренд: SYCLOPE electronic Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды