BOX 422 • TOWER, MN 55790 • USA • Tel (218) 753-2330 • www.lamppakuuma.com
20
InStaLLatIon
1. Mount the unit in the position most desirable to
your needs.
2. Connect the two leads to the appropriate power
source. Refer to blower name plate.
CautIon: a ground wire must run from the blower motor
housing to a suitable electrical ground such as a properly
grounded metallic raceway or ground wire system.
3. Wiring Diagram for Model 4C565A 2-speed blow-
er only.
NOTE: IF ONLY ONE SPEED IS USED, ISOLATE THE REMAIN-
ing leaD with eleCtriCians tape Or plastiC COnneC-
tOr.
MaIntenanCe
WarnInG: aLWayS DISConneCt PoWer SuPPLy Be-
Fore SerVICInG tHe BLoWer or WorkInG WItH tHe
unIt For any reaSon. tHIS IS eSPeCIaLLy IMPortant
WItH unItS eQuIPPeD WItH autoMatIC-reSet tHer-
MaL ProteCtIon. unIt May aCtIVate WItHout Warn-
InG!
LuBrICatIon
The motor should be re-lubricated every 6 months
with 10 or 20 drops of SAE 10W or 20W non-deter-
gent oil (ML-type) or with electric motor oil.
NO LUBRICATION FOR 1TDR9
GeneraL
Should further servicing of the unit be necessary, re-
fer to the “exploded” view illustration as an aid in dis-
assembly and assembly procedures.
limiteD warranty
Dayton blowers, Models 4C004A, 4C005, 4C008B, 4C012A, 4C013A, 4C264A, 4C446, 4C447,
4C448A, and 4C565A, are warranted by Dayton Electric Mfg. Co. (Dayton) to the original user against
defects in workmanship or materials under normal use (rental use excluded), or one year after date
of purchase. Any part which is determined to be defective in material or workmanship and returned
to an authorized service location, as Dayton designates, shipping costs prepaid, will be repaired or
replaced at Dayton’s option. For warranty claim procedures, see “Prompt Disposition” below. This
warranty give purchaser’s specific legal rights and purchasers may also have other rights which vary
from state to state.
WARRANTY DISCLAIMER. Dayton has made a diligent effort to illustrate and describe the products
in this literature accurately, however, such illustrations and descriptions are for the sole purpose of
identification, and do not express or imply a warranty that the products are merchantable, or fit for a
particular purpose, or that the products will necessarily conform to the illustrations or descriptions.
Except as provided below, no warranty or admission of fact, expressed or implied, other than as stated
in “LIMITED WARRANTY” above is made or authorized by Dayton, and Dayton’s liability in all events
is limited to the purchase price paid.
Certain aspects of disclaimers are not applicable to consumer products’ e.g., (a) some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you; (b) also, some states do not allow limitations on how long an implied
warranty lasts, consequently the above limitation may not apply to you, and (c) by law, during the
period of this Limited Warranty, any implied warranties of merchantability or fitness for a particular
purpose applicable to consumer products purchased by consumers, may not be excluded or other-
wise disclaimed.
PROMPT DISPOSITION. Dayton will make a good faith effort for prompt correction or other adjustment
with respect to any product which proves to be defective within warranty. For any product believed to
be defective within warranty, first write or call dealer from whom product was purchased. Dealer will
give additional directions. If unable to resolve satisfactorily, write to Dayton at address below, giving
dealer’s name, address, date and number of dealer’s invoice, and describing the nature of the defect.
If product was damaged in transit to you, file claim with carrier.
DAYTON ELECTRIC MFG. CO., 5959 W. HOWARD ST., CHICAGO, ILLINOIS 60648
FORM 5S2520
04040
MODELS 4C004A, 4C005, 4C006B, 4C012A, 4C013A,
4C284A, 4C446, 4C447, 4C448A, 4C565A, AND ITDR9
BLaCk (HIGH SPeeD)
WHIte (CoMMon)
reD (LoW SPeeD)
Green (GrounD)
Motor
trouBLe SHootInG CHart
symptOm
pOssible Cause(s)
COrreCtiVe aCtiOn
Excessive Noise.
1. Blower wheel contacting housing.
1. Realign or replace.
2. Foreign material inside housing.
2. Clean.
3. Leak in duct work.
3. Repair.
4. Loose duct work.
4. Secure properly
Insufficient air flow.
1. Leaks in duct work.
1. Repair
2. Dampers and/or registers closed.
2. Open.
3. Obstruction in system.
3. Remove
4. Clogged Filters.
4. Clean or replace.
Unite fails to operate.
1. Blown fuse or open circuit breaker.
1. Replace fuse or reset circuit breaker.
2. Defective motor.
2. Replace.
3. Automatic-reset thermal protector “tripped”.
3. Check for high (or low voltage input or ambi-
ent temperatures in excess of 40° C (104° F).
4. Motor improperly wired.
4. Re-wire.
