Laminex Metaline страница 17 Скачать руководство пользователя | Manualshive

Страница: 17 / 24

background image

Section 5: Kitchen Splashbacks

Installations

5.1 Items Required for Installation of Laminex Metaline Splashbacks

Sheet Inspection

• Double-sided tape – 3M VHB 4991 tape

or 3M Scotchtape 4008 (or equivalent)
in minimum 12.5mm width

•  Neutral Cure silicone
•  Silicone application gun
•  Glazier’s suction cup x 2
•  Straight edge/spirit level
•  Builders angle

Important Note: Minimum installation distance for gas and electric cooktops is
30mm

For all inbuilt gas and electric cooktops – Laminex Metaline splashbacks must
be installed with a minimum of 30mm set back from the edge of the appliance
(base plate). This applies to all gas, electric and induction cooktops. The minimum
benchtop width, for a cooktop installation, suitable for Laminex splashbacks is
600mm.

Important Note: Laminex Metaline Panels are not suitable as a splashback
for commercial gas cookers, domestic or commercial BBQ installations, or
freestanding cookers/ranges with rear vents.

30mm

30mm

150mm

150mm

200mm

200mm

590-610mm

490-510mm

85-
105mm

Figure 4:

Gas Hotplate clearances

Figure 5:

Electric Hotplate clearances

•  Measuring tape
•  Scraper or similar
•  Utility knife
•  3mm packers
•   Laminex Metaline splashback

panels

• Laminex Metaline metal edge

roller

«
...
15
16
17
18
19
...
»

Содержание Metaline

























Отзывы:

Нет отзывов

Похожие инструкции для Metaline

Pulsify S 24382 0 Series

Бренд: Hans Grohe Страницы: 2

Crometta Vario 6 l/min 26336404

Бренд: Hans Grohe Страницы: 6

Showerpipe 200 1jet Reno 26272000

Бренд: Hans Grohe Страницы: 24

Бренд: Helvex Страницы: 4

Бренд: Echogear Страницы: 8

Бренд: Olympia Страницы: 2

Бренд: SANPLAST Страницы: 20

IXMO 59551 010301

Бренд: KEUCO Страницы: 12

Бренд: Kohler Страницы: 2

Бренд: Kohler Страницы: 2

Бренд: Kohler Страницы: 2

Бренд: Kohler Страницы: 2

Бренд: Kohler Страницы: 8

Бренд: Kohler Страницы: 11

Бренд: Kohler Страницы: 20

Pfister Bellance 8P8-WS2-BLLS

Бренд: Spectrum Brands Страницы: 4

Monochrome Series

Бренд: Insignia Страницы: 33

Бренд: Insignia Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды