background image

 

16 

 

 
 
Operation Checklist

For a safe and pleasurable heating experience, perform this check before each use: 

 
Before Operating

1. I am familiar with entire owner’s manual and understand all precautions noted. 
2. All components are properly assembled, intact and operable. 
3. No alterations have been made. 
4. All gas connections are secure and do not leak. 
5. Wind velocity is below 10 mph. 
6. Unit will operate at reduced efficiency below 40 degrees F. 
7. Heater is for use outdoors (outside any enclosure). 
8. There is adequate fresh air ventilation. 
9. Heater is away from gasoline or other flammable liquids or vapors. 
10. Heater is away from windows, air intake openings, sprinklers and other water sources. 
11. Heater is at least 36 in. on top and at least 24 in. on sides from combustible materials. 
12. Heater is on a hard and level surface. 
13. There are no signs of spider or insect nests in heater orifices. 
14. All burner passages are clear. 
15. All air circulation passages are clear. 
16. Children and adults should be alerted to the hazards of high surface temperatures and should stay away to 
avoid burns or clothing ignition. 
17. Young children should be carefully supervised when they are in the area of the heater. 
18. Clothing or other protective material should not be hung from the heater, or placed on or near the heater. 
19. Any guard or other protective device removed for servicing the heater must be replaced prior to operating 
the heater. 
20. Installation and repair should be done by a qualified service person. The heater should be inspected before 
each use and at least annually by a qualified service person. 
21. More frequent cleaning may be required as necessary. It is imperative that control compartment burner and 
circulating air passageways of the heater be kept clean and free of debris and/or spider or insect nests. 

 
 

After Operation

1. Gas control knob is in OFF position. 
2. Gas tank valve is OFF. 
3. Disconnect gas line.

 

 
 
 
 
 
 
 
 
 
 
 
 

To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance 
activities on a regular basis: 

Keep exterior surfaces clean

1. Use soapy water for cleaning. Never use flammable or corrosive cleaning agents. 
2. While cleaning your unit, be sure to keep the area around the burner and control compartment dry at all times. 
Do not submerge the control valve assembly. If the gas control is submerged in water, do NOT use it. It must be 
replaced. 
3. Air flow must be unobstructed. Keep controls, burner, and circulating air passageways clean. Signs of possible 
blockage include: 

 

Gas odor with extreme yellow tipping of flame. 

 

Heater does NOT reach the desired temperature. 

 

Heater glow is excessively uneven. 

                                                                         

CARE AND MAINTENANCE 

 

OPERATING INSTRUCTIONS 

 

Содержание Fleur-de-lis




















Отзывы: