manualshive.com logo in svg

Labounty MSD Series, Безопасность, эксплуатация и обслуживание

Поделиться
Скачать
Labounty MSD Series Скачать руководство пользователя страница 23

MSD Legend Series Operation & Maintenance Manual | 23

HYDRAULIC INSPECTION

1. 

Wear personal protection equipment at all times. This 

includes eye protection, hard hat, steel toe shoes, 

leather gloves and hearing protection.

Trapped hydraulic pressure may be present after the 

base machine is shut off. Extreme caution must be 

taken when removing hydraulic hoses or lines. injury or 

death could result.

Locate flat, hard ground and place the attachment on the ground.

2. 

Check the hydraulic oil reservoir and ensure it is filled. 

3.  Visually inspect all hydraulic hoses and lines for leaks or damage.

SHEAR LUBRICATION

Use premium grease, No. 2EP. Grease fittings are shown with yellow “GREASE” decals. Each grease fitting 

requires .3 oz (8 g) of grease every 8 hours. This is about 6 shots of grease from an average grease gun.

Note: Follow all OeM lubrication instructions as it pertains to the cylinder and stick / boom connections.

CYLINDER 

CONNeCTiON

Lubrication Locations

Figure 17 

REAR CYLINDER PIN

STICK / BOOM CONNECTION

TurNTABLe BeAriNg

(BOTH SIDES)

MAiN PiVOT grOuP AND SLiDe SCreW

(BOTH SIDES)

SLiDe SCreW

(2 FITTINGS)

FRONT CYLINDER PIN

Содержание MSD Series





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды