LABORIE Nexam Pro CIM Скачать руководство пользователя

Страница: 48 / 278

Nexam Pro User Manual

Chapter 2

•

LABORIE EMG-PE (= disposable waterproof protected EMG surface

electrodes including lead wires) to be used with EMGC-3DIN-TP-40

(= guarded EMG cable with three x DIN42802 plug and three x DIN 42802
receptacle).

•

EMGC-3DIN-CN200 (short EMG adaptor cable with three x DIN42802 to

female DIN 5 and 200 cm reference lead), to be used for needle EMG
electrodes.

The color coding is as follows:

Red

Signal -

Black

Reference

Green / Yellow

The recommended EMG cable to use with the WPM or Luna is the UD 597 A6

(= guarded EMG cable for three surface electrodes with press studs, 60 cm).

Figure 2.36

EMG cable (for Luna or WPM)

The color coding is as follows:

Red

Signal -

Red

Reference

Black

2.5.11 Prepare the Flowmeter

The flowmeter can be used to measure the voided volume and the flow during
urodynamic investigations. The flowmeter is supplied with wireless Bluetooth

technology, so cabling is not required.

Содержание Nexam Pro CIM























































































































































































































































































Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды

LABORIE Nexam Pro CIM, Руководство пользователя

Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды