LABORIE Nexam Pro CIM Скачать руководство пользователя | Manualshive

Страница: 140 / 278

background image

140

Nexam Pro User Manual

Chapter 9

Ask the patient to squeeze and to maintain the squeeze. Press the

Start profile [Squeeze]

button. A window is displayed with the

distance you have to withdraw the catheter. Withdraw the catheter with
the speed and distance as displayed (setting in the protocol). After a

short while, there should be an increase in the anal pressure. The
software automatically marks the start and the end of the anal profile.

Reposition the catheter and repeat the procedure if necessary.

Variations

Instead of a rest profile it also possible to perform stress profiles similar to the

procedure described above. To perform a stress profile, let the patient cough
during the profile manometry. During the analysis, the software can calculate

transmission parameters for the peaks.

9.4.11 Balloon Expulsion Test

The purpose of the balloon expulsion test is to determine if the patient can

expel a balloon filled with a certain volume. The filled balloon simulates the
feces. Therefore, the best way to perform this test is to use water at body

temperature and a syringe or the pump module to fill the balloon with water.
In case of a multiuse catheter (without replacement of the balloon), it is

advised to fill the balloon with air (with a syringe) instead of water. This is to
prevent the balloon from sticking together.

Filling with water or air (syringe)

Press the

Next test

button until the text

Balloon expulsion

is

displayed on the left button. Fill the syringe with water (or air) according

to the volume displayed on the Syringe button in the upper-left corner
of the screen (e.g., 10 ml). Connect the syringe to the three-way

stopcock which is attached to the filling lumen of the catheter. Fill the
balloon.

Press the

Balloon expulsion

button to mark the start of the test. A

balloon marker is automatically inserted. Ask the patient to expel the
balloon.

«
...
138
139
140
141
142
...
»

Содержание Nexam Pro CIM























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Nexam Pro CIM

Бренд: FEAS Страницы: 72

Бренд: YYZ Lighting Страницы: 3

Бренд: Camp Safety Страницы: 118

Бренд: Ultrafast Systems Страницы: 39

Бренд: Mackworth Страницы: 2

Бренд: Mainca Страницы: 21

Бренд: Daktronics Страницы: 30

Бренд: DAKOTA ULTRASONICS Страницы: 28

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

GPSMAP 188 Sounder

Бренд: Garmin Страницы: 134

Бренд: Ultraflex Страницы: 3

Бренд: ABB Страницы: 33

FLEX-FOOT ASSURE

Бренд: Össur Страницы: 82

Бренд: Össur Страницы: 32

Digital Measuring System forUnloader & CTi CM...

Бренд: Össur Страницы: 6

DH Offloading Post-Op StyleShoe

Бренд: Össur Страницы: 32

Бренд: Össur Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды