background image

TECHNICAL SPECIFICATIONS

FILTER  SPECIFICATIONS

Type 

:  Transmitted Fluorescent illumination based on switching of     dichroic mirror 

cubes

Observation modes 

:  B-excitation and G-excitation

Lamp type  

:  HBO 50 W, high pressure Mercury vapor lamp

Supply Voltage 

:  110V AC, 60 Hz / 220V  AC, 50Hz

Operating environment 

:  Indoor use 

Ambient temperature 5 C to 40 C 

Maximum relative humidity 80% at 40 C

B-excitation

Excitation filter 

Transmission 90% at wavelength 420 to 480 nm.

Transmission 0% at wavelength 485 nm onwards.

Dichroic mirror 

Transmission 93% at wavelength 540 nm onwards 

.

Transmission 0% at wavelength 400 to 530 nm.

Barrier filter 

Transmission 95% at wavelength 535 nm onwards

Transmission 0% at wavelength 400 to 500 nm.

Recommended Fluorescent Dye 

Acridine Orange, both DNA & RNA 

G-excitation

Excitation filter 

Transmission 85% at wavelength 490 to 525 nm.

Transmission 0% at wavelength 530 nm onwards.

Dichroic mirror 

Transmission 90% at wavelength 600 nm onwards 

.

Transmission 0% at wavelength 400 to 595 nm.

Barrier filter 

Transmission 92% at wavelength 615 nm onwards

Transmission 0% at wavelength 400 to 575 nm.

TM

Recommended Fluorescent Dye 

Acridine Red FM  5-95 

Fluorescence Attachment User Guide 

9

Содержание TCM 400 FLR













Отзывы: