background image

 

Code 9

 

9.900.900.763 

 

 

13/19

 

U:\QA\Manualer\Arkiv\Manuals- Labogene-Origio-GKO\Manualer-WORD\ScanVac\CoolSafe

 XS  

XL Usermanual-Rev  A5.docx

 

 

1.

 

Ensure the CoolSafe is switched off and the vacuum has been released 

2.

 

Leave the condenser open to the atmosphere, introduce warm water into the 
condenser until it is released from the walls of the condenser. Then remove the 
ice 

In both cases, with or without electric de-icing, once the ice has been removed, open 
the drain valve to remove any remaining water. Thoroughly dry the condenser using 
disposable tissues, spray with alcohol and wipe dry, ensuring there is no retention of 
any liquid in the drain. 
 

5.6. Stopping the vacuum pump 

 

Close the (external) vacuum valve and let the pump run for a minimum of 45 
minutes after the freeze-drying has ended. This is to avoid any possible condensates 
remaining in the pump oil. 
 
If the freeze dryer is used regularly during the day/ week, it is recommended that the 
vacuum pump runs constantly with gas ballast valve open and the vacuum valve 
closed. 
 

6. Alarms and errors 

In case of alarms or errors, an alarm/error code will be displayed. 
 
E_1: Error indicating that the temperature sensor has a short circuit. 
 
E_2: Alarm indicating that the temperature during freeze-drying is above -40 °C. 
 
E_3: Error indicating that the temperature sensor is disconnected.

 

 

7. Maintenance 

 

7.1. CoolSafe  

The air-cooled condenser must be cleaned a minimum of twice a year. Use a vacuum 
cleaner and remove any dust in the cooling grill on the front. 
 

7.2. Vacuum pump 

See the Instruction Manual for maintenance according to the manufacture’s 
recommendations. Maintenance for a vacuum pump in general will be to: 

 

Check  the  oil  volume,  colour  and  condition  regularly.  The  oil  should  be 
changed  every  400-500  working  hours,  more  often  if  the  pump  has  been 
exposed to aggressive vapours. This is best done when the pump/oil is warm 
Keep a Log book of the usage periods. 

 

Drain the oil mist filter if the oil level is more than 10 mm. 

 

Drain,  clean  and  eventually  change  the  filter  insert  if  vapours  are  emitted 

Содержание SCANVAC CoolSafe 95-15 PRO Superior XL





















Отзывы: