Labnet C2500 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 12

Labnet C2500 Скачать руководство пользователя страница 9

Instruction Manual |

7

9.0 Troubleshooting Guide

Problem

Possible Cause

Solution

Centrifuge will not start

No power supply

Check that power is being supplied to
the outlet

Check that the power cord is plugged
into both the wall

outlet and the back of the centrifuge

Check that power cord is not damaged

Blown fuse

Check fuse and replace if necessary

Lid lock will not release

Defective lid lock

Open manually and have unit serviced

No power from PC board

Call for service

Lid lock is jammed

Call for service

Centrifuge is not receiving
power

See “Centrifuge will not start”

Centrifuge cannot be
started, although power
is on

Lid not closed correctly

Close lid correctly

No speed or time has been
selected

Set speed and/or time

bAL: Error Message
Indicates imbalance

Tubes not inserted
symmetrically in rotor holes

Load tubes symmetrically (see Section

3.4

on Loading the rotor)

Sample liquid in tubes not
balanced

Make sure the same volume of liquid is in
each tube

Defective or improperly
adjusted balance sensor

Call service

Lid: (Error message) Lid
not closed

Lid not closed completely

Close lid

Lid lock or sensor defective

Call service

Other Error Messages Er
on Display

–

Press time or speed knob to clear error

Call service

Should you have a question about the operation of the Labnet Prism™ Microcentrifuge or if service is
required, contact Customer Service. Do not send in a unit for service without first calling to obtain a
repair authorization number. Should the unit require return for service, it should be properly packed to
avoid damage. Any damage resulting from improper packaging shall be the responsibility of the user.

«
...
7
8
9
10
11
...
»

Содержание C2500













Отзывы:

Нет отзывов