Label NEPTIS PLUS Скачать руководство пользователя страница 38

38

F14

1

Function enabled 

if F12 = ON

OFF

Tests on opening safety sensor E.O. disabled; for sensors which are not pre-arranged for 

monitoring

S

ON

Test on opening safety sensors E.O. enabled; for sensors pre-arranged for monitoring by the 

automation (cat.2/pl.c). 

For details, refer to the paragraph "Safety sensors".

F15

1

Function active if 

F13 or 

F14 = ON

OFF

Safety sensors test with LOW logic level. 

For details, refer to the paragraph "Safety sensors".

S

ON

Safety sensors test with HIGH logic level. 

For details, refer to the paragraph "Safety sensors".

F16

OFF*

If  the  work  program  “Night  Lock”  is  selected,  the  door  remains  closed  and  can  only  be 

opened by actuating the OPEN-START inputs, or the Spyco radio control with the radio EN-

RF1 radio receiver.

ON

Selecting  the  work  program  “Night  Lock”,  the  door  opens  and  remains  open  10”  before 

reclosing to allow leaving the building.

F17

OFF*

Disabled function OFF

ON

Disabled function ON Refer to the paragraph “Courtesy operation for disabled” for details on 

the operating mode.

F18

OFF*

Operation with automatic closing

ON

Step-by-step function: an OPEN command opens the door; a second command is required 

to close back the door.

F19

Function enabled 

if F18 = ON

OFF*

In  the  step-by-step  function,  the  door,  when  open,  can  be  closed  only  with  a  closing 

command given by the OPEN-START input or by the Spyco radio control with the EN-RF1 

radio receiver.

ON

In  the  step-by-step  function,  the  door,  when  open,  automatically  closes  if  the  closing 

command is not given within 30 seconds.

F20

OFF*

Standard operation on the internal and external radar inputs.

ON

Operation with separate opening and closing commands. The external radar input controls 

the  opening,  the  internal  radar  input  controls  the  closing,  without  automatic  closing.  The 

OPEN and START inputs operate in standard mode.

F21

1

OFF

OPEN input configuration: normally closed contact.

When a device with N.C. contact is installed.

ON

OPEN input configuration: normally open contact.

When not in use or if a device with N.O. contact is installed.

F22

OFF*

The OPEN input is disabled in the work program “Manual free door”.

ON

The  OPEN  input  is  enabled  also  in  the  work  program  “Manual  free  door”,  to  allow  the 

automatic opening of the door.

F23

OFF*

Pause time with open door before constant automatic closing.

ON

Automatic increase of the pause time with door open if the door cannot close due to the high 

flow of people.

F24

OFF*

The pause time set by the potentiometer P4 is never reset.

ON

The pause time set by the potentiometer P4 is reset to the initial value if, with the door open, 

an opening command is given.

F25

For NB-

SMT/SMTB 

automations only

OFF*

In case of power failure, when mains supply is restored, the door remains in the current 

position.

ON

In  case  of  power  failure,  when  mains  supply  is  restored,  the  door  slowly  goes  to  closed 

position.

F26

OFF*

Interlock function disabled.

ON

Function of interlock between two doors enabled. A door may be opened only if the other one 

is closed. Please refer to the paragraph "Interlock system".

F27

Function enabled 

if F26 = ON

OFF*

In interlock function, door opening is delayed by 0.5” after the opening command. Please 

refer to the paragraph "Interlock system".

ON

In interlock function, door opening is immediate after the opening command. Please refer to 

the paragraph "Interlock system".

Содержание NEPTIS PLUS





































































Отзывы: