Labcyte Echo 520 Скачать руководство пользователя страница 46

Страница: 46 / 200

2-2

Echo Liquid Handler User Manual

2.1

Pre-installation requirements

2.1.1 Site requirements

The following site requirements must be met before installation:



Operating environment

of 19°–26°C (66°–79°F) and 10%–80%

relative humidity, non-condensing.



Sturdy, level, water-resistant bench top

capable of supporting

128 kg (283 lbs) with sufficient bench space to accommodate the
Echo liquid handler in a minimum operating envelope as follows (see
Figure 2.1):

Operating space envelope:

59 cm (23.2 in) width x 99 cm (39 in)

depth x 118 cm (46.5 in) height

Figure 2.1 Instrument layout on bench top

Top clearance:

25.4 cm (10 in) minimum above the instrument to

remove the top cover for servicing.

Note:

Less height clearance (>2.5 in) is acceptable if there is

sufficient space to lift the top and slide it all the way forward. Talk to
your Labcyte field engineer.

Front clearance:

sufficient clearance to load and unload microplates

by hand or by robot.

Side clearance:

2.5 cm (1 in) minimum on left and right sides.

59 c

m (2

3.2

in)

9 i

8 cm (46

.5 in)

Operating

Side clearance

2.5 cm (1 in)

30.5 cm (12 in)

Rear clearance

Top clearance

25.4 cm (10 in)

Envelope

7.6 cm (3 in)

Front clearance

Содержание Echo 520









































































































































































































Результаты поиска

Содержание Echo 520

Отзывы:

Labcyte Echo 520, Руководство пользователя, Страница: 46 / 200

Результаты поиска

Содержание Echo 520

Отзывы: