manualshive.com logo in svg

Labconco ScrubAir 46120 Series, Руководство пользователя

Поделиться
Скачать
Labconco ScrubAir 46120 Series Скачать руководство пользователя страница 26

Chapter 4: Using Your Washer Dryer

 

Product Service 1-800-522-7658 

22 

22 

The wash cycle can be terminated at any time by pressing and holding the 
RUN/CANCEL button. This will cause the washer to drain and end the current 
cycle. 
 

Alarms 

 
Throughout a wash cycle, there are several abnormal events that could occur.  The 
washer is programmed to monitor these occurrences and provide an alarm to alert 
the operator.  Information is shown on the display to identify the alarm situation.  
The following messages may be displayed.   
 
Lid Pause 

This displays if the Clear Lid has been removed or not in position. 
Operation of the wash cycle is delayed until the Clear Lid is replaced in 
the correct position. Once replaced the wash cycle will resume where it 
was interrupted. 

Fault-Drain 

This displays during the drain cycle if there is a No Water or Water Found 
fault.  Once the drain is complete one of two defaults will display as 
follows. 

Fault-No Water 

This displays if a water fill is inadequate.  The washer will cancel the 
cycle and drain any water that is in the washer.  The alarm is canceled by 
pressing RUN/CANCEL.  See Chapter 7: Troubleshooting – Washer will 
not fill. 

Fault- Water Found 

This displays if water is detected in the base of the Washer Dryer.  Water 
fill valves will be closed and the washer will cancel the cycle and drain 
any water that is in the washer.  The alarm is canceled by pressing 
RUN/CANCEL. See Chapter 7: Troubleshooting – Washer leaks. 
 

Fault-Temp Fail 

This displays on heated models only if the temperature sensor is not 
working properly.   The washer will stop the cycle.  The alarm is canceled 
by pressing correcting the fault  See Chapter 7: Troubleshooting – 
Temperature sensor failure. 
 

 
 
 

Содержание ScrubAir 46120 Series






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды