background image

H0071400W

Installation
and Operation
Instructions for

Mini-Therm II

Residential
Gas-Fired
Hydronic Boilers

Model JV
Sizes 50-225

FOR YOUR SAFETY: This product must be installed and serviced by a professional service technician,
qualified in hot water boiler installation and maintenance. Improper installation and/or operation could
create carbon monoxide gas in flue gases which could cause serious injury, property damage, or death.
Improper installation and/or operation will void the warranty.

WARNING

If the information in this manual is not followed exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a nearby phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or gas
supplier.

Vent damper is optional in some provinces of Canada.

These instructions are to be stored in the packet provided on the boiler.

Installation and Operation Instructions

Document 1025W

Содержание Mini-Therm II JV

























Отзывы: