Laars MASCOT LX страница 4 Скачать руководство пользователя

Страница: 4 / 56

LAARS Heating Systems

ASCOT

Figure 1.

Opening the Mascot LX.

The top and bottom panels come off when

pulled forward. This is true for all sizes.

START-UP

INSTRUCTIONS

SECTION 1.

General Information

WARNING

Mascot LX units

must

be installed in accordance with the procedures detailed in this manual, or the LAARS Heating

Systems warranty will be voided. The installation must conform to the requirements of the local jurisdiction having

authority, and, in the United States, to the latest edition of the National Fuel Gas Code, ANSI Z223.1/NFPA54. In

Canada, the installation must conform to the latest edition of CSA B149.1 Natural Gas and Propane Gas Installation

Code, and/or local codes. Where required by the authority having jurisdiction, the installation of Mascot LX boilers

must conform to the Standard for Controls and Safety Devices for Automatically Fired Boilers, ANSI/ASME CSD-

1. Any modifications to the boiler, its gas controls, or wiring may void the warranty. If field conditions require

modifications, consult the factory representative before initiating such modifications.

WIRING

DIAGRAM

RATING PLATE

Содержание MASCOT LX

























































Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды

Laars MASCOT LX, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды