background image

Page 4

3. Shut Down and Restart

3.1  To Start the FT Series Combi

       

 

If drained, please refer to the Install and Operating 

Manual to ensure that the complete ‘Setup’ 

procedure has been followed before starting this 

boiler. A complete ‘Setup’ must be performed by a 
qualified service person. 

 

3.2  Shutting Down the FT Series Combi

1.  Turn off the main electrical disconnect switch.

2.  Close all manual gas valves.

3.  If freezing is anticipated, drain the FT Series 

Combi and be sure to also protect building piping 

from freezing. All water must be removed from 

heat exchanger and condensate trap or else 

damage from freezing may occur. Please refer to 

the Install and Operating Manual. 

This step to be performed by a qualified service person.

4. The Control Display and Operation 

The FT Series Wall Mounted, Combination Boiler

Page 51

SECTION 5 

Control Display and Operation

5.1  Control Dial and Buttons

• Temperature Specifi cations

  Operating ambient Temperature Range : -10 to 60°C.

  Operating Relative Humidity up to: 90% at 40°C.

  Shipping & Storage Temperature Range of : -20 to 80°C.

Buttons

Function

Method

Function

Method

A

 Display 

Power

Turns Control Display  ON / OFF

Press/Tap

B

Modes

Status Display Mode (With display power on)

Press/Hold (5 Seconds)

Return to Menu (from 

Status Display Mode)

Press/Tap

Installer Mode (WIth display power off )

Press/Hold (5 Seconds)

Return  to  off   display  off  

mode (from installer mode)

Press/Tap

C

Hot 

Water

DHW Set point LOW Range 

95 - 120°F (35 - 49°C)

Press/Tap (To return home, 

tap Scroll/Select)

DHW set point HIGH  

Range 121-140°F (49.5-

60°C) (from DHW set 

point LOW RANGE)

Press/Hold (5 Sec-

onds),  (To return 

home, tap Scroll/

Select)

D

Central 

Heat

CH set point mode (boiler only)

Press/Tap (To return home, 

tap Scroll/Select)

Toggle (°C/°F) (from CH 

set point mode)

Press/Hold (5 

Seconds)

E

Scroll /

Select

Turn to scroll (clockwise or counterclockwise), 

Tap to select

Press/Tap

The Control Display

 has a Control Dial (E), 4 buttons (A, B, C, D), and a Liquid 

Crystal Display (with 72 back-lit segments).  This section of this manual gives 

instruction on how to navigate into the many functions of the FT and to change 

temperature set points, set system variables and controller parameters.

Status Light 

(constant green

when operating 

normally)

The Control Display

E

53page

B

C

A

D

Содержание FT Series













Отзывы: