Set up time: 15 minutes excluding time to fill with water.
Pool must be set up and assembled by adults only. Refer
to back page for important safety instructions for set-up
preparation and use. Only set up on completely level ground.
M I N N I D I P
®
Q U I C K S E T - U P
W A T C H S T E P - B Y - S T E P
V I D E O S
:
M I N N I D I P.C O M
1
OPEN BOTH FLAPS OF EACH
OF THE 3 AIR VALVES
The air valves have two ports and a plug. The main port (A)
is completely open, allowing air in and out quickly. The first
flap (B) is a one-way valve that allows air in, but not out.
The second flap (C) is a plug to secure air after fully inflated.
MAX WATER LINE
MINNIDIP TIPS
C
B
A
*
PUMP & BLOW DRYER
NOT INCLUDED
D
AIR VALVE
E
NO
GAP
GAP
SECURE ONE-WAY VALVES (B)
Once the open port is plugged with the one-way valve, grip
it between your thumb and index finger and push it securely
until there is absolutely NO GAP between the valves. If you
feel air escaping, make sure the black piece is fully inserted.
Important tip: Valves must be fully plugged as shown with no
gap or can result in an air leak once pool is filled with water—
especially the top ring as the bottom two rings will expand
once water is added and can pull the top ring valve loose if
not properly closed prior to filling with water.
3
INFLATE: ONE-WAY VALVE (B)
USING YOUR MOUTH (recommended)
Use your mouth to blow a few large breaths through this one-
way valve (about 5-6 breaths) to fill it as much as possible to get
the pool taut. This is an easy, and quicker, alternate to using an
air pump attachment as your breath has more force and fills it
quicker. Repeat on the middle ring, then the top.
USING AN AIR PUMP*
Use the same air pump attachment and insert into the black port,
angling the tip of the attachment towards the outer perimeter of
the valve so that the one-way valve flap lifts slightly to allow air
flow in. Repeat on the middle ring, then the top.
Once all rings are mostly filled, you may need to blow a little
more air through each one-way valve for pool to feel firm.
DO NOT OVER INFLATE and leave wrinkles in vinyl prior to
filling with water. Adding water will stretch vinyl and smooth it.
4
PLUG & SECURE VALVES (C)
Once each ring is inflated fully, plug with second flap (C). Then
firmly push each valve into pool so that it doesn’t get knocked
loose during use. Push firmly in center to fully secure valve.
5
FILL WITH FRESH WATER
First, make sure drain plug is securely plugged on the bottom floor.
Fill with clean water to the max water level, marked by wave icon.
Do not overfill, as too much water can put tension on seams and
may result in pool wall collapse and flooding, causing safety issues
and property damage. Please note: If filled to the max level,
the bottom two rings will expand wider than the top ring
due to water pressure.
6
INFLATE: OPEN PORT (A)
IMPORTANT: DO NOT OVER INFLATE. Do not attempt
to remove all wrinkles in vinyl. Pool vinyl will stretch and
air inside will expand in the heat. If over-inflated, it will
expand and compromise the seams when filled with water.
USING AN AIR PUMP*
Start inflating with the smallest air pump attachment
(D) by fitting snuggly into the open port. Fill as much as
possible, then
quickly
plug with the first flap without
letting too much air escape.
USING A BLOW DRYER*
Blow dryer
MUST BE COOL TO THE TOUCH
.
Start inflating by directing the air flow into the open port.
Do not touch metal of blow dryer to valve or vinyl of pool.
The blow dryer mouth (E) will not fit directly into the open
port, but you can direct air flow towards the opening. Wrap
your hand around the blow dryer and open port to help
direct air flow. Fill as much as possible, then
quickly
plug
with the first flap without letting too much air escape.
2
ENJOY & SHARE!
Now it’s time to dip in and enjoy!!
And don’t forget to share and tag
your pool party photos:
@MINNIDIP ##MINNIDIP
7
QUESTIONS? EMAIL US:
When draining water, GENTLY open drain valve flap, holding vinyl around plug down to avoid tearing vinyl or plug.
When not in use, ALWAYS empty water and store your MINNIDIP
®
out of direct sunlight and in a shaded location
to prevent fading caused by UV rays. NEVER leave filled with water to prevent drowning hazards and unhealthy water
contamination. Leaving filled with water for extended period of use, especially in extreme heat, can cause vinyl to
over-stretch and strain seams. NEVER add chlorine or any chemicals to the water to avoid vinyl and ink deterioration.
Do not store in below-room-temps (such as non-heated garages in winter) as it will compromise seams and cause leakage.
C A R I N G F O R Y O U R M I N N I D I P
®
