background image

INFLATE: OPEN PORTS (A)

 

USING AN AIR PUMP* 

Start inflating the bottom ring first with the smallest air 

pump attachment (D) by fitting snuggly into the open port. 

Fill as much as possible, then 

quickly

 plug with the first flap 

without letting too much air escape. Repeat on the middle 

ring, then the top. 

USING A BLOW DRYER* 

Blow dryer MUST BE COOL TO THE TOUCH. Start 

inflating the bottom ring first by directing the air flow into 

the open port. The blow dryer mouth (E) will not fit directly 

into the open port, but you can direct air flow towards the 

opening. You can also wrap your hand around the blow 

dryer and open port to help direct air flow. Fill as much as 

possible, then 

quickly

 plug with the first flap without letting 

too much air escape. Repeat on the middle ring, then the top.

2

Set up time: 10 minutes excluding time to fill with water. 

Pool must be set up and assembled by adults only. Refer 

to back page for important safety instructions for set-up 

preparation and use.

M I N N I D I P ™   Q U I C K   S E T - U P

WAT C H   S T E P - B Y - S T E P 

V I D E O S

:   

M I N N I D I P.C O M

1

OPEN BOTH FLAPS OF EACH  

OF THE 3 AIR VALVES  

The air valves have two ports and a plug. The main port (A) 

is completely open, allowing air in and out quickly. The first 

flap (B) is a one-way valve that allows air in, but not out.  

The second flap (C) is a plug to secure air after fully inflated.

INFLATE: ONE-WAY VALVE (B) 

 

USING YOUR MOUTH (recommended) 

Use your mouth to blow a few large breaths through this one-

way valve (about 5-6 breaths) to fill it as much as possible to get 

the pool taut. This is an easy, and quicker, alternate to using an 

air pump attachment as your breath has more force and fills it 

quicker. Repeat on the middle ring, then the top. 

 

USING AN AIR PUMP* 

Use the same air pump attachment and insert into the black port, 

angling the tip of the attachment towards the outer perimeter of 

the valve so that the one-way valve flap lifts slightly to allow air 

flow in. Repeat on the middle ring, then the top. 

 

Once all rings are mostly filled, you may need to blow a little  

more air through each one-way valve for pool to appear firm. 

As you inflate, stretch the pool out to get  air into the creases. 

Some wrinkles in the material will still exist even when pool is fully 

inflated. Do not over-inflate or attempt to remove every wrinkle.

MAX WATER 

LEVEL: BELOW 

TOP RING

When not in use, ALWAYS empty water and store your MINNIDIP™ out of direct sunlight and in a shaded location  

to prevent fading caused by UV rays. NEVER leave filled with water to prevent drowning hazards and unhealthy water 

contamination. Do not add chlorine or any chemicals to the water. Do not store in below-room-temperature conditions  

(for example, in non-heated garages during the winter), as it will compromise the vinyl seals and cause air leakage. 

C A R I N G   F O R   Y O U R   M I N N I D I P ™

HA

VE

 S

O

 M

U

C

H

 F

U N

 M I N NID

IP

PI

N

G

!

C

B

A

*

PUMP & BLOW DRYER   

NOT INCLUDED

D

AIR VALVE

E

NO 

GAP

GAP

SECURE ONE-WAY VALVES (B)

Once the open port is plugged with the one-way valve, 

grip it between your thumb and index finger and push it 

securely until there is NO GAP between the valves. If you 

feel air escaping, make sure the black piece is fully inserted. 

3

4

PLUG & SECURE VALVES (C) 

Once each ring is inflated fully, plug with second flap (C). Then tuck 

each valve into pool so that it doesn’t get knocked loose during use.

5

FILL WITH FRESH WATER 

First, make sure drain plug is securely plugged on the bottom floor. 

Then, slowly fill with clean water to the max water level, marked 

as being below the top ring. Fill no more than 12 inches deep with 

water. Do not overfill the pool as doing so may result in pool wall 

collapse and flooding, causing safety issues and property damage. 

6

ENJOY & SHARE!

Now it’s time to dip in and enjoy!!  

And don’t forget to share and tag  

your pool party photos:

@MINNIDIP

#MINNIDIP

7

QUESTIONS? EMAIL US: [email protected]

Отзывы: