manualshive.com logo in svg

L3 Systems KeyAT-4, Руководство пользователя

Поделиться
Скачать
L3 Systems KeyAT-4 Скачать руководство пользователя страница 6

KeyAT-4 Keyboard Port Adapter

 

5/19/2007

 

4 

L3 Systems

 

Sending Data 

The main job of the KeyAT is to transfer data from the RS-232 port and send it through 
to the computer's keyboard port.  Data can be sent using ASCII, ASCII control codes, 
DOS scan codes, keyboard scan codes or ASCII hex.  A line can have a maximum 
length of 80 characters and should end with an <ENTER> (CR, hex 0D). When using 
immediate mode, data and commands are interpreted as received, and buffered up to 80 
characters.  If you get more than 80 characters ahead of the computer, the additional 
characters will be ignored.  

In line turn-around mode, the KeyAT sends a colon prompt after the data has been 
processed, signaling that it is ready for another command. The example shows the ASCII 
characters ‘DIR<ENTER>’ being sent through the KeyAT.

  

Example:

 

    

KeyAT, V4.0x1, [C]L3 Systems, Inc. 2005 

  :DIR^M<ENTER> 

  : 

Commands 

Commands are instructions to the KeyAT to do something other than just pass data 
through to the computer.  All commands begin with a ~ (tilde, hex 7E) character followed 
by a command character and then in some cases some data. 

~@  Disable Commands

 – All commands are disabled until 10 consecutive tildes 

(~~~~~~~~~~) or reset/power cycle. 

~~~~~~~~~~ 

Reset/Enable Commands

 – If commands are disabled, sending 10 

consecutive tilde (~) characters will enable commands.  If commands 
are enabled, this will reset the KeyAT (& run power-up string if 
loaded). 

Data Mode Commands 

The four mode commands set the way data is interpreted by the KeyAT.  A mode is set 
until another mode is given or until a power failure occurs.

 

~C 

Character Mode

 - is the default mode of operation.  When this mode is set, any 

ASCII character except ~ (tilde, hex 7E), ^ (caret, hex 5E), and CR (return, hex 
0D) is converted to the scan codes for that character.  Each ASCII character will 
be sent to the computer with the corresponding “make” and “release” codes.  
Allow enough time for the codes to be sent through to the computer. 

Control codes may be sent by a combination of a ^ (caret, hex 5E), and the 
corresponding letter.  For example, a control C (Hex 03) is ^C. 

~H 

Hex ASCII Mode

 - Data is interpreted as hexadecimal encoded ASCII.  For 

example, to send the computer the character 'A', you would need to send its 
hexadecimal ASCII value (Hex 41) as two ASCII digits, 4 and 1. 

Содержание KeyAT-4





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды