manualshive.com logo in svg

L-Card E20-10, Руководство пользователя

Поделиться
Скачать
L-Card E20-10 Скачать руководство пользователя страница 16

 

E20-10 

 

User Manual  

 

3.3.  Module configuration 

3.3.1.  Standard supply package 

•

 

module 

E20-10 (1 

pcs.) 

•

 

communication cable on USB 2.0 (1 pcs.) — 

А-В type, length of 1.3...2.0 m

 

•

 

network card for 

E20-10

 power supply from alternate current network of 220 V, 50 Hz 

•

 

magnetic sweep cable of connector  (1pcs.) — 

DB-37M 

with housing DP-37P —  for 

digital signal cable terminating production 

•

 

magnetic sweep cable of connector  (1pcs.) — 

DJK-10A 

— for extern power supply 

circuit cable terminating production, if required, to energize 

E20-10

 not from circuit of 

220V through attached network card but from different source of  +9...+27 V 

•

 

magnetic sweep cable of connector  (1pcs.)  — 

MDN-9P 

— for production of magnetic 

sweep cable to external device power supply outputs of ±12 V and to DAC outputs.  

•

 

CD-ROM with documents and software. 

Attention!

 DAC is not included in standard supply package (p.

3.3.2

). 

If required, use hub stations, power units for them and auxiliary USB-cables. When dealing 

with 

E20-10

 the user must buy this equipment by himself in third-party manufacturers.  The same is 

related to not included in delivery package interconnecting wires, auxiliary cables, connectors and 
terminals to connect signal sources and arrange network interface communications. 

3.3.2.  Design versions 

E20-10

 is produced in the following design versions: 

Design version 

Description 

E20-10  

Basic design version — without DAC,  bandwidth of 1.25 MHz per 
ADC channel 

E20-10-D     

2-channel DAC bandwidth of 1.25 MHz of each ADC channel. This 
version was named as "E20-10D" in old notation 

E20-10-1     

Without DAC, bandwidth of 5 MHz of each ADC channel (design 
version is av

ailable for revision В only)

 

E20-10-D-1   

With 2-channel DAC, bandwidth of 5 MHz of each ADC channel 

(design version is available for revision В only)

 

Attention!

 Specify the required design version in ordering 

E20-10

. 

Design version is specified on factory label on the body bottom.   

 

Another ADC channel bandwidths are available as agreed upon with 

L-Card

.  

 

Содержание E20-10




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды