L.B. White Big Bertha 334 Скачать руководство пользователя страница 13

Страница: 13 / 18

ATTENTION

This procedure is to be done once a year prior to the heating

season, anytime the heater is moved from one job location

to the next, or after servicing the heater.

MATERIALS REQUIRED

(To be secured through local purchase)
QQuuaannttiittyy

DDeessccrriippttiioonn

High Pressure Gas Gauge capable of

reading up to 35 PSIG

1/4 in. Tee

1/4 in. Nipple

A. PREPARATION

1. Close fuel supply valve at LP gas supply container.
2. Allow heater to burn off gas remaining in it’s gas

supply line..

3. Close manual main burner valve on heater.
4. Remove gas hose from heater.
5. Remove hose adapter from inlet of pilot safety control

valve.

B. GAUGE INSTALLATION

1. Connect the following materials together in the order

as given. See Fig. 10.

-- Tee to inlet of pilot safety control.
-- Nipple to tee.
-- Hose adapter (as removed earlier) to nipple.
-- Gas hose to hose adapter.

2. Tighten all connections securely.
3. Connect gauge to tee.

C. READING PRESSURES

1. Start the heater. With the heater operating, the

pressure gauge should read the pressure specified

on the dataplate or in the specification section of this

owner’s manual.

2. Does the pressure reading at the inlet of the safety

control agree with that given on the dataplate? If so,

no further checking or adjustment is required.

Proceed to section D.

3. If the inlet pressures do not agree with that specified

on the dataplate, then check the following:

-- Improper regulator for heater.
-- Blockage in gas hose.
-- Insufficient size or quantity of LP gas supply

containers.

D. COMPLETION

1. Once the proper inlet pressure has been confirmed,

close fuel supply valves.

2. Allow heater to burn off fuel remaining in gas supply

line.

3. Remove gauge, hose adapter, nipple and tee.
4. Reconnect hose adapter to inlet of safety control

valve and hose to hose adapter.

5. Tighten all connection securely and check for gas

leaks.

Gas Pressure Checks

WAARRNNIINNGG

■

Do not disassemble the pilot safety control valve.

■

Do not attempt to replace any components of the pilot

safety control valve.

■

The pilot safety control must be replaced if any

physical damage occurs to it.

■

Failure to follow this warning will result in fire or

explosions, leading to injury or death, and building

damage.

HIGH PRESSURE GAUGE

HOSE

NIPPLE

TEE

PILOT
CONTROL
VALVE

HOSE ADAPTER
(FROM PILOT VALVE INLET)

FIG. 10

1133

Содержание Big Bertha 334



















Результаты поиска

Содержание Big Bertha 334

Отзывы:

Похожие инструкции для Big Bertha 334

Бренды по названию

Популярные бренды

L.B. White Big Bertha 334, Инструкция и руководство пользователя

Результаты поиска

Содержание Big Bertha 334

Отзывы:

Похожие инструкции для Big Bertha 334

Бренды по названию

Популярные бренды