L-Acoustics S Series Скачать руководство пользователя страница 31

Страница: 31 / 80

Inspection and preventive maintenance

Inspection and preventive maintenance

How to do preventive maintenance

Inspect the system before any deployment and after any corrective maintenance operation.
Perform preventive maintenance at least once a year.

Rigging and hardware

Perform the

Rigging part inspection

(p.32) on each rigging part.

Use the

Mechanical system overview

(p.33) to identify critical parts of the system and apply the specic checks

described in the

Inspection references

(p.38).

Do the

Rigging check

(p.39).

If any parts are damaged, contact your L-Acoustics representative for further instructions.

Acoustics

Perform the

Enclosure check

(p.40).

Perform the

Listening test

(p.42) to detect any degradation in sound quality.

If necessary, refer to the

Corrective maintenance

(p.57) section for speaker repair kits and maintenance instructions.

Syva owner's manual (EN) version 1.0

Содержание S Series

















































































Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды

L-Acoustics S Series, Руководство пользователя

Результаты поиска

Содержание S Series

Отзывы:

Похожие инструкции для S Series

Бренды по названию

Популярные бренды