background image

L-ACOUSTICS LA15a 115V Manual V1.0  27/01/2003   

 

                  4

 

!

7.  Do not operate the amplifier near heat producing devices such as radiators, heat registers, 

stoves or any other apparatus that produces heat. 

8.  Always operate the unit with the chassis ground wire connected to the electrical safety earth. 

Do not defeat the safety purpose of the grounding-type plug. A grounding-type plug has two 
pins and a third grounding prong. The third prong is provided for your safety. If the provided 

plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 

9.  Connect only to AC power outlets rated 100-120 V, 50-60 Hz. 
10. Do not use this amplifier if the power cord is broken or frayed. Protect the power cord from 

being walked upon or pinched - particularly at the plugs and the point where the power cord 

exits from the apparatus. 

11.  Only use accessories specified by the manufacturer. 
12.  The unit is intended to be mounted in a 19” rack. Follow the mounting instructions outlined in 

this manual and always rear support the unit when used in portable applications. When a rack 
on wheels is used for portable applications, use caution when moving the loaded rack in order 
to avoid injury from tipping over. 

13.  Unplug this apparatus during lightning storms or when unused for long periods of time. 
14. Do not connect an amplifier output in parallel or series with any other amplifier’s output. Do 

not connect the amplifier output to any other voltage source, such as a battery, mains source, 

or power supply, regardless of whether the amplifier is turned on or off. 

15.  Do not run the output of any amplifier back into another channel's input. 
16. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has 

been damaged in any way such as: 

• 

Power supply cord or plug is damaged 

• 

Liquid has been spilled into the unit 

• 

An object has fallen into the unit 

• 

The unit has been exposed to rain or moisture 

• 

The unit does not operate normally 

• 

The unit was dropped or the enclosure is damaged 

17. Do not remove top or bottom covers. Removal of the cover will expose hazardous voltages. 

There are no serviceable parts inside and removal may void the warranty. 

18.  An experienced user shall always supervise the use of professional audio equipment, especially 

if inexperienced adults or minors are using the equipment. 

2.5 USER RESPONSIBILITY 

2.5.1 SPEAKER DAMAGE 

  Your amplifier is very powerful and can be potentially dangerous to both loudspeakers and 

humans alike. Loudspeakers can be damaged or destroyed by overpowering, especially with 

the high power available from a bridged amplifier. Always check the loudspeaker’s continuous 

and peak power handling capabilities. Note: even when using the amplifier’s front panel attenuator to 
reduce the gain, it is still possible to reach full output power if the input signal level is high enough. 

2.5.2 SPEAKER OUTPUT HAZARD 

  Power amplifiers are capable of producing hazardous output voltages. To avoid electrical 

shock, do not touch any exposed speaker wiring while the amplifier is operating. Refer to 

Section 6.2 concerning proper connection of loudspeakers. 

2.5.3 RADIO INTERFERENCE 

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 

!

Содержание LA15a
























Отзывы: