manualshive.com logo in svg

L-Acoustics L-ISA Processor II, Руководство пользователя

Поделиться
Скачать
L-Acoustics L-ISA Processor II Скачать руководство пользователя страница 26

Operation

IN/OUT

The IN and OUT LEDs display the state of the input and output channels.

red

the level reaches the maximum level

orange

the level reaches -5 dBFS (5 dB below the maximum level)

green (high)

the level reaches -20 dBFS (20 dB below the maximum level)

green (low)

the level reaches -60 dBFS (60 dB below the maximum level)

off

the level is more than 60 dB below the maximum level

Emergency USB key

L-ISA Processor II is provided with an emergency USB key. In the rare case of the start-up sequence of L-ISA Processor II

failing because of defective hard drive, the USB key can be used to temporarily keep the processor running during live

shows.
If the emergency key is defective or missing, contact your Certied Provider or your L-Acoustics representative for

replacement instructions.

Preparing and updating the emergency USB key

The emergency USB key must be congured and regularly updated to be immediately usable in case of hard drive

failure.

Equipment

• computer with L-ISA Controller version 2.3.x minimum
• CAT5e U/FTP cable

Procedure

1.

Run L-ISA Controller.

2.

Update L-ISA Controller to the latest version.

3.

Connect the CONTROL Ethernet port of the processor to an Ethernet port of the computer running L-ISA Controller.
Use a CAT5e U/FTP cable.

4.

Check that the processor is detected as available in the 

Processors

 view.

Refer to the 

L-ISA Controller Help

.

5.

Update the rmware of the processor to the latest version.

6.

Write down the settings and congurations dened in all the tabs of the 

Processors

 view for later use.

7.

Power off the processor.

8.

Connect the emergency USB key to the USB 1 or USB 2 port on the rear panel, or to the USB port on the front panel.

9.

Power on the processor.
The processor boots up on the USB backup system.

10.

Update the rmware of the USB backup system to the latest version.

11.

In 

Processors

 view, recongure the settings and congurations as written down in step 

6

 (p.26) on the USB

backup system.

26 

 L-ISA Processor II owner's manual (EN) version 1.0

Содержание L-ISA Processor II













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды