KYOWA MRS-100 Series Скачать руководство пользователя страница 12

Страница: 12 / 81

1-3. Combination models

MRS-114A (4ch-Receiver) is used in combination with MRS-104A-S, MRS-101A-S (1ch-Strain Transmitter),

MRS-101A-SE (1ch-Strain Transmitter (EXT Antenna)). or MRS-101A-V (1ch-Voltage Transmitter).

Connect to a power supply that matches the power specifications.

Receiver

Transmitter

MODEL

Product name

MODEL

Product name

MRS-114A

4ch-Receiver

MRS-104A-S

4ch-Strain Transmitter

MRS-101A-S

1ch-Strain Transmitter

MRS-101A-SE

1ch-Strain Transmitter

(EXT Antenna)

MRS-101A-V

1ch-Voltage Transmitter

Do not use the MRS-10A for the MRS-114A.

If already using MRS-10A, uninstall MRS-10A, upgrade to MRS-10B, and then respecify the

Transmitter and Receiver [Pairing settings].

For details, see the MRS-10B instruction manual.

The latest version of MRS-10B can be downloaded from our company

’

s website.

NOTE

The MRS-10B software Ver. is displayed on the titlebar.

MEMO

The Transmitter and Receiver Firmware Ver. can be confirmed from MRS-10B.

The Transmitter and Receiver Firmware Ver. can be confirmed by clicking the [Receiver Information]

button in the case of the MRS-114A, or by clicking the [Transmitter Information] button on the

[Transmitter Settings] tab in the case of the MRS-104A-S or MRS-101A-S/SE/V.

MEMO

Содержание MRS-100 Series


















































































Результаты поиска

Содержание MRS-100 Series

Отзывы:

Похожие инструкции для MRS-100 Series

Бренды по названию

Популярные бренды

KYOWA MRS-100 Series, Инструкция по эксплуатации

Результаты поиска

Содержание MRS-100 Series

Отзывы:

Похожие инструкции для MRS-100 Series

Бренды по названию

Популярные бренды