manualshive.com logo in svg

Kyoritsu Electrical Instruments Works, Ltd. KEW 6010B, Инструкция по эксплуатации

Поделиться
Скачать
Kyoritsu Electrical Instruments Works, Ltd. KEW 6010B Скачать руководство пользователя страница 19

— 17 —

7. LOOP IMPEDANCE TESTS

DISCONNECT THE INSTRUMENT FROM THE CIRCUIT UNDER TEST 

BEFORE OPERATING THE FUNCTION SWITCH

TO SELECT THE LOOP TESTING RANGE SELECT

“

LOOP

”

7.1

 

Voltage Measurement

Power on the instrument. When the tester is set to the Loop test function, mains 

voltage is displayed as soon as the instrument is connected for test. This 

voltage display is automatically updated every 1 second.

7.2

 

What is earth fault loop impedance?

The path followed by fault current as a result of a low impedance fault occurring 

between the phase conductor and earth is called earth fault loop. Fault current 

is driven round the loop by the supply voltage, the amount of current depending 

on the voltage of the supply and on the impedance of the loop. The higher the 

impedance, the lower will be the fault current and the longer it will take for the 

circuit protection (fuse or circuit breaker) to operate and interrupt the fault.

To make sure that fuses will blow or that circuit breakers will operate quickly 

enough in the event of a fault, the loop impedance must be low, the actual 

maximum value depending on the characteristics of the fuse or the circuit 

breaker concerned. Every circuit must be tested to make sure that the actual 

loop impedance does not exceed that specified for the protective device 

concerned.

For a TT system the earth fault loop impedance is the sum of the following 

impedances (See Fig 9):

Fig 9

○   Even though the test current in the 2000 ohm range (15mA test current) is low  

some RCD's may trip due to sensitivity or where there may already be 

additional leakage in the circuit being tested.

○ The  Loop  impedance  in  a  TN  system  is  small  and  therefore  it  is  not 

recommended to test in the 2000 ohm range. RCD's will have to be bridged to 

avoid tripping when using other test ranges.

Содержание KEW 6010B





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды