manualshive.com logo in svg

Kyoeisha BARONESS LM56GC, Руководство по эксплуатации для владельца

Поделиться
Скачать
Kyoeisha BARONESS LM56GC Скачать руководство пользователя страница 68

Installing The Reel Cutter (Cutting Cylinder)

Caution

Both the reel cutter (cutting cylinder) and the
bed knife (bottom blade) are edged tools.
Handle them carefully, since they could cut
your hands and feet.

Caution

When handling the reel cutter (cutting
cylinder) or bed knife (bottom blade), wear
gloves to protect your hands.
Pay attention not to let the reel cutter (cutting
cylinder) catch your gloves. Otherwise, you
may injure your hand or fingers.

Follow the steps below to replace the
bearings and oil seals on the left and right
ends of the reel cutter (cutting cylinder).

Important

Use 30204JRP6 as bearing.

Fill up the bearings and oil seals with
grease (Excelite EP No. 2).
Install the reel cutter (cutting cylinder) onto
the frame.
Tighten the nut until the length of the spring
reaches 11.5 mm (0.453 in), and then lock
it.
Note:
Preloading with a constant force by spring
pressure is possible.
Measure the rotating torque of the reel
cutter (cutting cylinder) with a torque
wrench.
The specified value is 0.8 to 1.0 N·m (8 to
10 kgf·cm).
Specification without groomer:

3

1

2

A

wggg9e-020

Installing The Reel Cutter (Cutting Cylinder)_001

1.

2.

3.

4.

1

Washer

2

Left-hand nut

3

Torque wrench

A

11.5 mm (0.453 in)

Specification with groomer:

3

1

2

A

wggg9e-021

Installing The Reel Cutter (Cutting Cylinder)_002

1

Reel gear

2

Reel gear fixing nut

3

Torque wrench

A

11.5 mm (0.453 in)

LM56GC

・

LM66GC / LM66TC

Maintenance

Page 5-14

Maintenance Work

Содержание BARONESS LM56GC


























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды