Kyocera Ryobi W-1850, Руководство по эксплуатации для владельца

Страница: 6 / 7

1. Dust extraction outlet
2. Blade guard retracting lever
3. Lower guard
4. Bevel angle locking knob
5. Upper guard
6. Front handle
7. Rear handle
8. Trigger switch
9. Safety button
10. Cutting depth locking knob
11. Spindle lock
12. Hex wrench
13. Parallel guide fence
14. Blade
15. Hex bolt
16. Outer flange
17. Inner flange
18. Parallel guide fence locking knob
19. Base plate
20. Washer
1. While pressing the spindle lock (11), turn the hex bolt (15)
with hex wrench (12) until the gear shaft locks.
2. Loosen the hex. head bolt by turning the wrench
counterclockwise while the spindle is locked.
3. Remove the hex head bolt, washer (20) and the outer flange
(16).
4. Retract the lower guard (3) back with the blade guard
retracting lever (2) as far as possible toward the upper guard
(5).
5. Attach the saw blade (14) against the inner flange (17) on
the gear shaft and then attach the outer flange and the hex
bolt with washer (20).
6. Press the spindle lock lever again, and tighten the hex head
bolt by turning clockwise while the spindle is locked.
WARNING! Do not use any abrasive wheels
ATTACHING AND REMOVING THE SAW BLADE
(Fig.2, 3)
• BE SURE TO DISCONNECT THE TOOL FROM THE
POWER SUPPLY BEFORE ATTACHING AND
REMOVING THE SAW BLADE.
• BE SURE THAT THE TEETH OF THE SAW BLADE
ARE POINTING UPWARD AT THE FRONT OF THE
TOOL. (The logo and specs printed on the blade should
be visible from the outside) the blade by hand.
Check for damage to the tool, parts and accessories which may
have occurred during transportation. Take some time to read this
manual carefully and understand all the content prior to
assembly and operation.
Sawing and mitre cutting all types of wood.
Do not use for cutting metal or masonry.
Always operate on a flat surface. Check and ensure the working
surface is flat and sturdy before operation. (Fig. 4)
Always operate with both hands. Using one single hand during
operation is dangerous and not allowed. (Fig. 5)
CAUTION
Always ensure that the tool is switched off and
unplugged from the mains supply before assembly.
Voltage:
Power input:
No load speed:
Blade diameter:
Blade arbor:
Blade teeth:
Max. cutting depth
at 90°:
at 45°:
Net weight:
220-240V
〜・
50/60Hz
1500W
6000min
-1
Ø185mm
Ø20mm
24T
64mm
48mm
3.9kg
WARNING!
WARNING!
6
SPECIFICATIONS
DESCRIPITION
INTENDED USE
Parallel guide fence, Hex wrench
STANDARD ACCESSORIES
ATTACHING
1. While pressing the spindle lock lever, turn the hex. head bolt
with hex. wrench until the gear shaft locks.
2. Loosen the hex bolt by turning the wrench counterclockwise
while the spindle is locked.
3. Remove the hex. head bolt and the outer flange.
4. Retract the lower guard back with the lower guard lever as
far as possible toward the safety guard.
5. Remove the saw blade. Attach the outer flange and the hex.
head bolt on the spindle to avoid missing.
REMOVING
ASSEMBLY
OPERATION
- Check that the lower blade guard (3) fully retracts when the
blade guard retracting lever (2) is moved towards the front of
the upper guard (5).
- Check that the lower blade guard returns completely to cover
the blade in rest position.
- Cut at a speed suited to the work piece. (Work slowly when
work piece is hard.
- Inspect the saw blade frequently and replace or sharpen if dull,
to avoid overloading the motor.
- To minimize dust, an extraction system can be attached to the
extraction port.
BEFORE USING THE TOOL