Kyocera PF-760 Скачать руководство пользователя страница 18

Страница: 18 / 59

5H8

1-2-3

1-2-3 Installing the cassette heaters (option)

Installing the cassette heater requires the following component:

Cassette heater set: for 220 - 240 V specifications

Supplied parts of cassette heater set:

Two (2) cassette heaters (P/N

AVGR02967B

): for 220 - 240 V specifications

Two (2) cassette heater retainers

Six (6) M4 x 6 IT tap-tight (S-tight) screws

One (1) relay wire
Nine (9) wire saddles

Procedure

1. Remove two screws from each of the right

cover and left cover 4 and then the covers.

2. Remove three screws holding the paper

feeder rear cover and then the cover.

3. Open the paper feeder.
4. Remove two screws holding the paper con-

veying unit assembly and then the assem-
bly.

Figure 1-2-2

5. Fit the cassette heaters to the cassette

heater retainers using two screws and wire
saddle for each.

6. Fit the cassette heater retainers to the left

and right of the paper feeder using one
screw for each.

Figure 1-2-3

7. Pull the cassette heater cable out to the

machine rear through the cable hole.

Screw

Paper conveying
unit assembly

Machine left

Cassette heater

Wire saddle

Cassette heater
retainer

Screws

Screw

Machine right

Cassette heater
retainer

Cassette heater

Screws

Screw

Wire saddle

Y1120

Service Manual

Содержание PF-760



























































Результаты поиска

Содержание PF-760

Отзывы:

Похожие инструкции для PF-760

Бренды по названию

Популярные бренды

Kyocera PF-760, Руководство по обслуживанию

Результаты поиска

Содержание PF-760

Отзывы:

Похожие инструкции для PF-760

Бренды по названию

Популярные бренды