Kyocera FS-C1020MFP+ Скачать руководство пользователя

Страница: 108 / 175

System Maintenance Reference

Waste Toner Bottle Set Error



Waste toner bottle not set



Disconnected or defective harness of the waste toner bottle set sensor



Defective waste toner bottle set sensor

014

1. Install the waste toner bottle.

2. Check or replace the harness of the waste toner bottle set sensor.

3. Replace the waste toner bottle set sensor.

Tray/Paper Selection Error



No paper in the tray or tray not set in the machine



Paper size requested by the job does not match the paper in the tray

030

1. Install the tray or put the correct size paper in the tray.

2. Check the paper setting in the user menu mode.

Paper Selection Error: Feed and Exit



Paper size requested by the job does not match the paper in the tray



Selection error for the paper feed and paper exit location in duplex mode

031

Check the paper feed and exit location in the user menu mode.

Jam Error: No Feed from Tray 1



Paper

slipped

050

Remove the paper jam at tray 1.

Jam Error: No Feed from Optional Tray



Paper

slipped

052

Remove the paper jam at the optional tray (Tray 2).

Содержание FS-C1020MFP+
















































































































































































Результаты поиска

Содержание FS-C1020MFP+

Отзывы:

Похожие инструкции для FS-C1020MFP+

Бренды по названию

Популярные бренды

Kyocera FS-C1020MFP+, Руководство по обслуживанию

Результаты поиска

Содержание FS-C1020MFP+

Отзывы:

Похожие инструкции для FS-C1020MFP+

Бренды по названию

Популярные бренды