Kyocera ECOSYS FS-C2126MFP Скачать руководство пользователя страница 178

Страница: 178 / 206

Troubleshooting

8-4

Error Messages

When an error occurs, the display may show one of the error messages listed below. These will help you identify
and correct the problem.

NOTE:

When a transmission error occurs, a sent/receipt result report is produced. Check the error code

shown in the report and refer to the

Error Code List on Appendix-12

for a description. To print the sent/receipt

result report, refer to

Send Result Reports on page 5-5

and

FAX RX Result Reports on page 5-6

You may also check error codes using the activity report. (Refer to

Activity Report on page 5-8

Message

Checkpoint

Corrective Action

Reference

Page

Machine failure.
Call service.

–

Turn the main power switch
off and on, or unplug the
power cord and plug it in
again. If the message still
appears, note the error code.
Turn the main power switch
off and unplug the power
cord. Call your service
representative.

–

Polling box limit exceeded.
Job is canceled.

–

Polling box capacity is used
up with document data.
Press the

key. The job is

canceled.
Try to perform the job again
after printing or deleting the
data in the polling box.

4-32

Job Accounting restriction
exceeded.

–

The number of paper used
has exceeded the limit
preset by Job Accounting.
No further operation is
possible. Press the

key.

The job is canceled.
Try to perform the job again
after resetting the limit for
paper use.

Refer to the
machine’s

Operation
Guide

Job Accounting restriction
exceeded.
Cannot scan.

–

Fax transmission is
prohibited by Job
Accounting. No further
operation is possible. Press
the

key. The job is

canceled.
Check the setting for Job
Accounting.

Refer to the
machine’s

Operation
Guide

Содержание ECOSYS FS-C2126MFP















































































































































































































Результаты поиска

Содержание ECOSYS FS-C2126MFP

Отзывы:

Похожие инструкции для ECOSYS FS-C2126MFP

Бренды по названию

Популярные бренды

Kyocera ECOSYS FS-C2126MFP, Руководство по эксплуатации

Результаты поиска

Содержание ECOSYS FS-C2126MFP

Отзывы:

Похожие инструкции для ECOSYS FS-C2126MFP

Бренды по названию

Популярные бренды