7
7
1
1
4
6
3
17
13
13
2
5
8
9
2
3
15
16
14
4
22
12
11
1
20
2
5
3
17
8
20
10
7
10
9
12
11
8
6
82mm
9mm
13
13
22
22
21
20
20
18
23
23
- 3 -
- 4 -
DESCRIPTION
1. Front shoe
12. Blade adjusting screw
2. Rear shoe
13. Lock button
3. Adjustment knob
14. Metal part of dust bag
4. Handle
15. Dust bag
5. Belt cover
16. Dust guide
6. Knob bolt
17. Depth-of-cut-scale
7. Switch
18. Side plate
8. Hex. head bolt
9. “T” type wrench
20. Blade (H.S.S Type)
10. Blade binder
21. Blade sharpening holder
11. Blade adjustment gauge 22. Stand
23. Screw
SPECIFICATIONS
Capacities planing depth
1 mm (3/64”)
planing width
82 mm (3-1/4”)
Input
550 W
Rotation speed
18,000 min
-1
Overall length
309 mm (11-1/2”)
Weight
2.6 kg (5.7 lbs.)
STANDARD ACCESSORIES
“T” type wrench, Side plate, Knob bolt,
Philipps screwdriver, Blade adjustment gauge,
Blade sharpening holder, Screw
APPLICATIONS
(Use only for the purposes listed below.)
1. Planing wood.
REPLACING THE BLADE (Figs. 1, 2)
BE SURE TO DISCONNECT THE TOOL FROM THE
POWER SUPPLY BEFORE REMOVING OR REPLAC-
ING THE BLADE.
1. Remove the hex. head bolts (8) with the “T” type
wrench (9) provided.
2. Remove the blade binders (10) and blades (20).
3. Place the new blades on the cutter block.
4. Replace the blade binders and hex. head bolts.
ADJUSTING THE BLADE (Figs. 1, 3)
1. Loosen hex. head bolt (8) with the “T” type wrench
(9).
2. Rotate the cutter block until the tip of the blade is
vertically in line with the shaft center.
3. Adjust the blades (20) using the blade adjustment
gauge (11) and the blade adjusting screws (12).
4. The blades should be set so that their entire length
is level with the stationary rear shoe (2).
5. Tighten the hex. head bolt.
SWITCH (Fig. 4)
This tool is started and stopped by depressing and releasing
the switch (7).
For continuous operation, press the lock button (13) while
switch is depressed. Depress again to release the lock.
ATTACHING THE DUST BAG (Optional Accessory)
(Fig. 5)
1. When mounting the dust bag (15), open the dust bag
by squeezing the metal part of dust bag (14).
2. Attach the dust bag to the dust guide (16).
3. Although the bag is of ample size, it should be
emptied frequently and shaken out to maintain
efficiency.
4. Opening the zipper on the bottom of the dust bag
allows complete cleaning.
The dust bag can be removed with the opposite
method to that mentioned above.
ADJUSTING THE PLANING DEPTH (Fig. 6)
The planing depth can be adjusted from approximately
0mm-1mm. To adjust the depth, turn the adjustment knob
(3) to the desired setting on the depth-of-cut scale (17).
Always work from a rough cut to a finish cut. For rough
planing use a setting from 0.5mm to 1mm. For finish
planing use a setting from 0.2mm to 0.4mm.
CAUTION!
DO NOT TURN THE DEPTH ADJUSTMENT KNOB
MORE THAN THE MAXIMUM PLANING DEPTH OF
1MM.
OPERATING INSTRUCTIONS (Fig. 7)
1. Be sure the work piece is clamped or otherwise
firmly secured.
2. With one hand holding the depth adjustment knob(3)
and the other gripping the handle(4), place the front
shoe on the edge of the piece to be planed.
3. Before starting the planer, be sure the blades are not
in contact with the work piece.
4. Position the planer so that the front shoe(1) is
perfectly flat and level on the piece to be worked.
5. Using a slow, steady motion, begin planing with the
motor at full torque.
6.
IMPORTANT!
Be especially careful to keep the planer flat and
level at the beginning and the end of planing
work. Tilting of the machine can cause the
excessive planing of the edge of the work
material.
STAND (Fig. 8)
A stand (22) is provided so that the blade can be protected
when the tool is not being used.
The stand automatically raises when the tool is used and
lowers again when the operation is completed.
When you do not want to use the stand, raise it before
starting the operation.
SIDE PLATE (Fig. 9)
The side plate (18) helps to plane long and uneven
surfaces accurately.
EDGE PLANING (Fig. 10)
This planer has a precision machined groove in the middle
of the front shoe for bevel planing.
Before planing good timber, make a few cuts on a piece of
scrap timber to determine the desired depth.
RABBETTING (Fig. 11)
Install the side plate. Before working the actual piece,
determine the desired depth using a piece of scrap wood.
While planing, the side plate should rest on edge of the
work piece. The maximum rabbet cut depth is 9mm.
ATTACHING THE VACUUM (Fig. 12)
The dust can be collected by using a vacuum cleaner.
Connect the vacuum cleaner hose to the dust guide (16).
SHARPENING BLADES (Fig. 13)
1. Fasten the blade (20) to Blade sharpening holder (21)
with four screws (23).
Be sure both blade edges face in the same direction.
2. Place the blade edges so that they rest flat on the
grinding stone (not included -- must be purchased
separately) .
3. Firmly grip the Blade sharpening holder and move it
back and forward to sharpen the blades.
CAUTION ; Do not hold the grinding stone by hand.
Hold it by the clamp or vise.
MAINTENANCE
After use, check the tool to make sure that it is in top
condition.
It is recommended that you take this tool to an Authorized
Service Center for a through cleaning and lubrication at
least once per year.
DO NOT MAKE ANY ADJUSTMENTS WHILE THE
MOTOR IS IN MOTION.
A LW AY S D I S C O N N E C T T H E P O W E R C O R D
FROM THE RECEPTACLE BEFORE CHANGING
REMOVABLE OR EXPENDABLE PARTS (BLADE, BIT,
SANDING PAPER ETC.), LUBRICATING OR WORKING
ON THE UNIT
WARNING!
To ensure safety and reliability, all repairs should be
performed by an AUTHORIZED SERVICE CENTER or
other QUALIFIED SERVICE ORGANIZATION.
S AV E T H E S E I N S T R U C T I O N S FO R F U T U R E
REFERENCE.
“ WARNING
To reduce the risk of injury, user must
read instruction manual ”
“
Class II construction tool in which protection
against electric shock does not rely on basic
insulation only, but in which additional safety
precaution, such as double insulation or reinforced
insulation, are provided.”
