KYLAND Technology PTS-DR200 Скачать руководство пользователя

Страница: 37 / 55

Kyland Technology (Shanghai) Co., Ltd PTS-DR200 Time Server

- 35 -

Items

Parameters

Description

Local: Make output time working at Local format.

IRIG-B

Mode

Even

Odd

Set IRIG-B check code for O4.
Even: Use Even mode check code to code IRIG-B signal;
Odd: Use Odd mode check code to code IRIG-B signal.

IRIG-B

Polarity

Set IRIG-B output signal polarity for O4.
+: positive polarity DC, high level is 1;
-: negative polarity DC, low level is 1.

Press ‘Save’ button to save the current setting when you change setting.

If select ‘O5’ in Channel Group, the setting screen will be shown as:

[Figure 3-22] Output Setting Screen (O5)

Table 21 – Output Setting (O5)

Items

Parameters

Description

IRIG-B

Second

Compensation

Set second compensation offset for O5.
Unit is second(s);
Range is between -999999999s and 999999999s.
Default value is 0s.

IRIG-B

PPS

Compensation

0ns

Set PPS compensation offset for O5.
Unit is nanosecond(ns);
Range is between -250000000ns and 250000000ns.
Default value is 0ns.

IRIG-B

Time

Format

UTC

TAI

Local

Set reference time for IRIG-B output signal of O5.
UTC: Make output time working at UTC format;
TAI: Make output time working at TAI format.
Local: Make output time working at Local format.

Содержание PTS-DR200
























































Результаты поиска

Содержание PTS-DR200

Отзывы:

Похожие инструкции для PTS-DR200

Бренды по названию

Популярные бренды

KYLAND Technology PTS-DR200, Руководство по эксплуатации

Результаты поиска

Содержание PTS-DR200

Отзывы:

Похожие инструкции для PTS-DR200

Бренды по названию

Популярные бренды