Kwikset SmartCode 909 Скачать руководство пользователя страница 5

2-3/8" (60 mm)

2-3/4" (70 mm)

Backset 

 

Distancia al centro

Centerline

Linea central

1-

3/

8" (

3

5 mm)

1-

3/

4" (

44 mm)

2-

1/

4" (

5

7 mm)

Face of the door

Frente de la puerta

Edge of the door

Borde de la puerta

Fold

Doble

Installation Guide

Guía de instalación

1-800-327-5625 • www.kwikset.com

If drilling a new door, use 
the supplied template and 
the complete door drilling 
instructions available at  
kwikset.com/doorprep

Si va a perforar una 
puerta nueva, utilice la 
plantilla suministrada y las 
instrucciones completas para 
la perforación de la puerta 
en kwikset.com/doorprep

Parts in the box

Piezas en la caja

Required tools

Herramientas necesarias

*Passage knobs only: Call 
Kwikset to order a service kit 
for 2-1/4" (57 mm) thick doors.

*Perillas de paso solamente: 
Llame a Kwikset para pedir un 
kit de servicio para puertas 
gruesas con un espesor 
de entre 57 mm (2-1/4").

Latch

Pestillo

Passage Knobs

Perillas de paso

Screws

Tornillos

Strike

Placa

Privacy 
Knobs

Perillas de 
privacidad

Emergency Unlock tool 
(privacy locks only)

Herramienta para el 
desbloqueo de emergencia
(las cerraduras de 
privacidad solamente)

Not required for all applications

No se requiere para todas 

las aplicaciones

2-3/8" (60 mm)

 or • o

2-3/4" (70 mm)

1-3/8"–1-3/4"*

35 mm–44 mm*

2-1/8"

54 mm

1"

25 mm

Do not remove 
screws!

¡No retire los 
tornillos!

Hold the latch in front of the door hole, with 
the latch face flush against the door edge.

Sostenga el pestillo en frente del orificio 
de la  puerta, con la cara del pestillo 
al ras con el borde  de la puerta.

If the latch holes are centered in the door hole, 
no adjustment is required. Proceed to step 4.

If the latch holes are NOT centered, adjust 
latch.  See “Latch Adjustment” (step 3C).

Si los orificios del pestillo están centrados con el orificio 
de la puerta, no se requiere ajustarlo. Vaya al paso 4.

Si los orificios del pestillo NO están centrados, ajuste 
el pestillo. Consulte “Ajuste del pestillo” (el paso 3C).

Latch Adjustment (only if needed)

Ajuste del pestillo (si es necesario)

Drilling Template

Plantilla de perforación

Move the pin to 
extend the latch.

Mueva el pasador 
para extender 
el pestillo.

Template is only needed if a new hole must be drilled in the door.

La plantilla solo se necesita en caso de que deba 

perforarse un nuevo orificio en la puerta.

62820 / 01

Additional tools 
(if needed)

Herramientas adicionales 
(si es necesario)

wood block

bloque de madera

not centered

no centrado

centered

centrado

Instructions continue on reverse 

Las instrucciones continúan en el reverso de la hoja

Twist the side 
with the holes. 

Gire el lado con 
los orificios.

counter-clockwise

sentido antihorario

Pull to 

separate 

knobs. 

Tire para 

separar las 

perillas.

 A

 

C

 

D

H

F

K

E

J

G

 B

A

A

B

C

Set knobs aside until step 5.

Deje a un lado las perillas hasta el paso 5.

A

B

C

 or • o

Prepare door and check dimensions

Prepare la puerta y revise las dimensiones

1

Disconnect knobs (if pre-assembled)

Desconecte las perillas (si previamente ensambladas)

2

Adjust the backset of the latch (if needed) 

Ajuste la distancia al centro del pestillo (si es necesario)

3

Содержание SmartCode 909







Отзывы: