KVH Industries TracVision UHD7 Скачать руководство пользователя | Manualshive

Страница: 27 / 41

background image

25

Connecting the TV-Hub to an onboard local area
network (LAN) allows the user to access the
TV

-

Hub’s web interface using any device

connected to the network (see Figure 41).

NOTE:

Connecting the TV-Hub to the onboard

network using its Wi-Fi rather than an Ethernet cable
is not recommended because you lose the ability to
connect directly to the TV-Hub’s built-in Wi-Fi. You
will always need to connect via the network.

NOTE:

The Reset button on the rear panel of the

TV

-

Hub (see Figure 42) reverts all network settings

back to their original factory settings.

Wired LAN Connection

a.

Connect the “Ethernet” port on the TV-Hub

to the onboard network (LAN) using the

supplied Ethernet cable.

b.

By default, the TV

-

Hub’s Ethernet port is

configured as a DHCP client, and the

network’s router automatically assigns it an

IP address. However, in this

Dynamic

mode,

the TV

-

Hub could get assigned a different IP

address whenever it is turned on.

KVH recommends that you set the TV

-

Hub

to

Static

mode and enter a static IP address at

the web interface (see Figure 43) (go to

Settings > Network Settings). Be sure to

choose a static IP address that is outside the

router’s DHCP range (refer to the router’s

user manual for details on finding its range).

Figure 41: TV-Hub Network Connections

Onboard Network (LAN)

12VDC

POWER

Reset

Ethernet

Internet

4

3

2

1

TV-Hub

Wireless Router

Ethernet

Figure 42: TV-Hub Reset Button

TV-Hub

Figure 43: Web Interface Ethernet Settings

Connect to an Onboard Network

17

Optional

«
...
25
26
27
28
29
...
»

Содержание TracVision UHD7










































Отзывы:

Нет отзывов

Похожие инструкции для TracVision UHD7

Бренд: Alien Страницы: 24

MS-MBA-3.2-H4-L4

Бренд: Matsing Страницы: 5

Aironet AIR-ANT2568VG-N

Бренд: Cisco Страницы: 6

OmPlecs TOP 200 AMR

Бренд: ANTONICS Страницы: 2

RocketDish RD-5G30

Бренд: Ubiquiti Страницы: 12

AirMax AMY-9M16

Бренд: Ubiquiti Страницы: 16

AirFiber X AF-5G34-S45

Бренд: Ubiquiti Страницы: 18

Бренд: Ubiquiti Страницы: 20

AllinOne HAWAII 3G AIS

Бренд: RR Electronic Страницы: 7

Бренд: ETS-Lindgren Страницы: 12

Бренд: ETS-Lindgren Страницы: 33

Бренд: Sirio Antenne Страницы: 2

Бренд: Garmin Страницы: 176

Бренд: ClearStream Страницы: 2

Бренд: Ten-Haaft Страницы: 28

Бренд: TAGSYS RFID Страницы: 23

Бренд: Steren Страницы: 2

Бренд: Steren Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды