KVH Industries TracPhone V7-HTS Скачать руководство пользователя

Страница: 3 / 11

Step 3 - Replace the LNB

There are three possible LNB types installed in the
antenna. Identify the LNB

by sight

, then continue

to the relevant page to replace the LNB.

You can find the antenna serial number on the Support

page of the ICM’s web interface or the System Info menu
on the ICM’s front panel.

Antenna LNB

Serial No.

Kit Part No.

Go to

Legacy LNB-1

150300408 and earlier

NOTE: Since the filter is inside
the original LNB being replaced,
an external filter is added to the
new LNB.

72-0797

includes:
• LNB & filter

assembly

• Feed tube

• ICM

page 4

LNB-1 with Filter

150300409 through 150800889

NOTE: Replace LNB/filter
assembly.

72-0797

includes:
• LNB & filter

assembly

• Feed tube

• ICM

page 5

LNB-1 without Filter

150800890 through 170100021

NOTE: Filter is inside the OMT.

72-0790

includes:
• LNB

• Feed tube

• ICM

page 6

LNB-3 (HTS Ready)

170100022 and later

NOTE: An “HTS Ready”
antenna only requires updates to
belowdecks equipment.

72-0821

includes:
• 10 MHz

reference

• ICM

page 8

Содержание TracPhone V7-HTS












Результаты поиска

Содержание TracPhone V7-HTS

Отзывы:

Похожие инструкции для TracPhone V7-HTS

Бренды по названию

Популярные бренды

KVH Industries TracPhone V7-HTS, Инструкции по преобразованию

Результаты поиска

Содержание TracPhone V7-HTS

Отзывы:

Похожие инструкции для TracPhone V7-HTS

Бренды по названию

Популярные бренды