KVH Industries TracPhone V3HTS Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 52

background image

37

Follow these steps to connect the vessel’s phone.

Connect the Vessel Phone

Using the supplied RJ-11 cable, connect the
customer’s analog (not digital) phone or PABX to
the “Voice Line 1” jack on the ICM (see
Figure 74).

Figure 74: Connecting the Vessel Phone (Example)

B2

Voice Line 1

Vessel Phone

1

ICM

Do not connect anything to the “Voice Line 2”

jack. Only “Voice Line 1” is enabled for use.

IMPORTANT!

Connect Voice Line Equipment

20

«
...
36
37
38
39
40
...
»

Содержание TracPhone V3HTS





















































Отзывы:

Нет отзывов

Похожие инструкции для TracPhone V3HTS

Бренд: Cambium Networks Страницы: 3

75cm Offset Antenna

Бренд: Patriot Страницы: 16

Бренд: M2 Antenna Systems Страницы: 3

Бренд: NARDA Страницы: 26

Бренд: KVH Industries Страницы: 13

VISION SCIBORG TR365D

Бренд: Kiramek Страницы: 12

Бренд: INAC Страницы: 23

104590-1 FPD.5-5.8-18

Бренд: Radio Waves Страницы: 5

Бренд: Televes Страницы: 4

Бренд: Televes Страницы: 32

Бренд: Solid Signal Страницы: 2

Бренд: MFJ Enterprises Страницы: 5

Бренд: H3C Страницы: 6

Бренд: H3C Страницы: 7

Бренд: Hawking Страницы: 2

Бренд: Labgear Страницы: 2

Бренд: Ubiquiti Страницы: 10

Бренд: Velleman Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды