70
0-D
C
Q
U
IC
K S
TA
R
T
70
0-D
C
Q
U
IC
K S
TA
R
T
Power-Down
Power-UP
Verify Area is safe, power and air are applied,
E-Stops are out and Fence Gates are closed.
1. At the Electrical Box, turn the
Electrical Dis-
connect
to the ON position.
2. Turn the
Control Circuit Switch t
o the ON
position.
(Approximately 3 minute boot-up)
3. Push the
Start
button
.
All the 6 lights should be illuminated.
See re-
verse side for the 6-Light Description.
1. Push the Stop button.
2. Turn the Control Circuit Switch to the OFF
position.
3. Turn the Electrical Disconnect to the OFF
position on the Electrical Cabinet.
700-DC Quick Start rev 1
• Ensure the proper staple guns are enabled and staples
are loaded.
• Adjust the machine for the desired Door Width.
• Adjust the Machine for Door Length
• Adjust the machine for the Jamb Height.
• Select the door hand by way of the
Reset Left
or
Reset Right
switch. (See Step 1)
Mechanical Setup
Before processing the door, set the following mechanical
adjustments.
See the back of this Quick Start for information on these
setting
s.
Note:
Some of these settings are options and may not be
located on your machine.
Main Panel Setup
Before processing the door, verify or change the set-
tings at the Main Panel to match your job.
• Enable or Disable the Movable and Fixed Sill and
Head Guns.
• Set the Staple patterns for Head and Sill Modes.
Start the Process
5. Ensure the hinge jamb is in the correct position in relation to the head jamb.
At the
Head End,
push both Hand Free Buttons to
clamp the Header.
6. Push both Sill Hands Free Buttons.
(Drops the door to lower position).
7. Set Sill in place. Push both Sill Hand Free Buttons
(Clamps the door.)
8. Fire Staple Guns.
Simultaneously press the Fire Guns Button and the Right
Hand Free Button to fire all enabled staple guns.
9. Push both Sill Hand Free Buttons
(Un-Clamp door.)
10. Pull out the Door.
Note:
If changing the hand of the door, repeat Step 1.
Note:
To
move back a step
at any time during the process,
• Turn the Sill Sequence Switch to the
REV
position.
• Press both Hands Free buttons to move back a step.
• Repeat pressing the buttons until the desired step is reached.
• After the desired step is reached, switch back to the
FWD
position.
• Continue forward from the last step selected.
Step through the process to frame a door by using the button controls
located at the Head and Sill ends of the machine.
1. To
select the door hand.
Simultaneously select Reset Right (RH) or
Reset Left (LH) and the Right Sill Hands Free Button.
2. Pull in the door;
verify header is clear so the Stapler Heads can come
in. Have a little wiggle room.
3. Push both Sill Hand Free Buttons..
(Brings in movable fence staplers.)
4. Insert
the
Jamb
and
Header
.
Machine Action
Control Action
Choose Hand
Right Hand Hands Free Reset Right or Reset Left
Bring in Side Staple Guns
(Sill End) Both Hands Free Buttons
Clamp the Head
(Head End) Both Hands Free buttons
Lower Door
(Sill End) Both Hands Free Buttons
Clamp the Door
(Sill End) Both Hands Free Buttons
Fire Staple Guns
Right Hand Hands Free Fire Button
Unclamp
(Sill End) Both Hands Free Buttons
Sill Insert
Jamb Insert
Header Insert
Check Alignment
OR
OR
View machine videos at:
https://www.youtube.com/user/kvalinc
To view 700-DC specific videos, enter 700-DC
on the page search line.
Control Sequence Summary
