background image

1. SYNC IN:

This balanced XLR Jack accepts the SYNC output from another PA unit using a standard mic cable. 

Channels from both units are summed together. Use the channel volume controls to get the mix of the channels (If a channel is not 

used turn the volume all the way down). MASTER volume controls the loudness of the mix. It does not affect volume of a linked PA 

product. 

Note: The shield connection (pin 1) on this jack is connected to chassis ground. It is not lifted.

2. SYNC OUT:

This balanced XLR Jack accepts the SYNC input from another PA unit using a standard mic cable. 

Channels from both units are summed together. Use the channel volume controls to get the mix of the channels (If a channel is not 

used turn the volume all the way down). MASTER volume controls the loudness of the mix through the primary unit, not the linked unit. 

This jack may also be used to connect the PA product to the balanc ed line input of a power amp. 

Note: The shield connection (pin 1) on this jack does not connect to chassis ground, it is lifted.

3. Bluetooth LED (PA40BATBT ONLY): 

Indicates that a Bluetooth equipped device has successfully paired with the PA40BATBT.

4. CHARGING LED: 

Indicates the battery is charging. It is recommended to charge for 12 hours after use. Battery charges even if the 

unit is ON under normal volume conditions. When played loud, the battery will stop charging to allow higher power demand. To resume 

charging, uplug AC power cord, then reconnect after 10 seconds.

Note: LED indicates “rapid charge” stage and will turn off when unit enters “float charge” stage.

5. BATTERY LEVEL INDICATOR: 

During use, the BATTERY LEVEL indicator LED’s show the remaining battery power. When the red 

light on the left is on, turn off the unit and recharge to avoid excessive battery drain.

6. AC Power Cord Receptacle & Fuse Holder:

 

Insert the AC cord firmly into the AC receptacle. Power circuit is on whenever AC cable is connected to unit and plugged into wall. 

Be sure to use the cable provided with your PA40BATBT. The power cord can be removed for storage or replacement if damaged.  

Note: Replace the AC cord if its protective jacket is damaged or ground pin is damaged or removed.

 

7. Power:

 This switch activates power to the Battery Powered PA. 

Note:

 

Power is supplied to the unit for charging even if Power switch is off.

2

1

4

6

5

3

7

PA40BATBT:

BLUETOOTH PAIRING INSTRUCTIONS

To connect your Bluetooth device to the 

Kustom Bluetooth receiver for the first 

time, navigate to the Bluetooth settings menu 

on you Bluetooth enabled device.  Ensure that 

Bluetooth is enabled and your Kustom 

product is powered on.  Perform a scan for 

available devices.  Select and pair to the 

Kustom product in the list of available 

devices.  Enter 0000 for the passcode if 

prompted.  Once paired, a connection can be 

established.   Depending on the device, future 

connections may be established automatically 

when a previously paired Bluetooth device is in 

range of the Kustom Bluetooth receiver.

The Bluetooth receiver in Kustom Bluetooth 

products is an A2DP device and will work with 

other A2DP compatible Bluetooth devices 

including most smart phones.  Additional 

hardware and/or driver software may be 

required for computers with integrated Bluetooth 

adaptors due to a lack of support for A2DP 

devices by some operating systems.

A2DP protocol only allows for one to one device 

connections.  Therefore, only one Bluetooth 

device can be connected to a Kustom 

Bluetooth product at one time.  Similarly, a 

Bluetooth device can only be connected to one 

Kustom Bluetooth product at one time.  

Plugging a 1/8” connector into the AUX jack 

disables the Kustom Bluetooth receiver.

Содержание PA40BATBT











Отзывы: